Pass Cisco 200-301 Exam in First Attempt Guaranteed!
Get 100% Latest Exam Questions, Accurate & Verified Answers!
30 Days Free Updates, Instant Download!
Cisco 200-301 Practice Test 39
Question 380
Network review: Two WAN providers offer the same destination prefix and one static route should remain standby behind a primary. Which TWO proposed shortcuts would be unsafe in this situation? Select TWO answers.
Explanation
Correct Answer
Two WAN providers offer the same destination prefix and one static route should remain standby behind a primary. “Use the same exact administrative distance and assume the backup will never share forwarding” would violate the requirement. A floating static route stays out of the RIB while a lower-distance route to the same prefix is available, then becomes active when that route vanishes.
Two WAN providers offer the same destination prefix and one static route should remain standby behind a primary. “Set the backup static route distance lower than the primary and expect it to stay idle” would violate the requirement. A floating static route stays out of the RIB while a lower-distance route to the same prefix is available, then becomes active when that route vanishes.
Incorrect Answers
Two WAN providers offer the same destination prefix and one static route should remain standby behind a primary. “collect targeted evidence to inspect show ip route, configured static route distance, OSPF adjacency and tracked interface reachability” adds a relevant safeguard or verification step rather than weakening the solution. A floating static route stays out of the RIB while a lower-distance route to the same prefix is available, then becomes active when that route vanishes.
“install a backup static route with an administrative distance higher than the active primary route” is the controlled implementation, not an unsafe workaround. A floating static route stays out of the RIB while a lower-distance route to the same prefix is available, then becomes active when that route vanishes.
“confirm the repair by checking that show ip route chooses the primary normally; after a controlled primary failure the backup static route appears and connectivity recovers” adds a relevant safeguard or verification step rather than weakening the solution. A floating static route stays out of the RIB while a lower-distance route to the same prefix is available, then becomes active when that route vanishes.
Question 381
Consider this operational failure: A small branch requires all otherwise-unmatched internet traffic to leave via ISP next hop 203.0.113.1. What should the administrator implement first?
Explanation
Correct Answer
The action 'Configure a reachable 0.0.0.0/0 static default route toward the approved upstream next hop.' directly addresses the ipv4 default static route requirement in this situation: A small branch requires all otherwise-unmatched internet traffic to leave via ISP next hop 203.0.113.1. The relevant network mechanism is that the IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred. A successful change should show that show ip route displays S* 0.0.0.0/0 and an external traceroute follows the upstream, while local routes still use local interfaces. To distinguish a genuine correction from a superficial change, inspect show ip route 0.0.0.0, recursive next-hop reachability, upstream return routing and NAT policy.
Incorrect Answers
“Set a /32 default that matches only 0.0.0.0 rather than every unknown destination” does not implement the control that the facts call for. Instead, configure a reachable 0.0.0.0/0 static default route toward the approved upstream next hop.
“Use an unreachable default next hop and assume every internet packet still leaves” would not meet the requirement. Instead, configure a reachable 0.0.0.0/0 static default route toward the approved upstream next hop.
“Replace every internal connected route with 0.0.0.0/0” does not implement the control that the facts call for. Instead, configure a reachable 0.0.0.0/0 static default route toward the approved upstream next hop.
Question 382
While troubleshooting 'A small branch requires all otherwise-unmatched internet traffic to leave via ISP next hop 203.0.113.1.', which underlying protocol rule should guide the decision?
Explanation
Correct Answer
The IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred. Show ip route displays S* 0.0.0.0/0 and an external traceroute follows the upstream, while local routes still use local interfaces.
Incorrect Answers
The choice “A host ARPs for its on-link default gateway to send off-subnet packets; a gateway outside the local prefix cannot normally be resolved directly” concerns ipv4 host default gateway; it does not resolve the stated requirement. The IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred.
“Routing metric ranks candidate paths learned through the same protocol; OSPF path cost is based on configured interface costs, not simply hop count” pertains to routing metrics within one protocol, not the deciding condition here. The IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred.
The choice “Administrative distance expresses a routing information source's trustworthiness; Cisco connected AD 0, static AD 1 and OSPF AD 110 by default” concerns route administrative distance; it does not resolve the stated requirement. The IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred.
Question 383
Which measurable result should be checked before closing this ticket: A small branch requires all otherwise-unmatched internet traffic to leave via ISP next hop 203.0.113.1.
Explanation
Correct Answer
The observation 'show ip route displays S* 0.0.0.0/0 and an external traceroute follows the upstream, while local routes still use local interfaces.' specifically demonstrates a successful outcome for ipv4 default static route in this case: A small branch requires all otherwise-unmatched internet traffic to leave via ISP next hop 203.0.113.1. That observation tests the underlying mechanism that the IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred. It is stronger evidence than a healthy unrelated service because it exercises the path affected by the remedy to configure a reachable 0.0.0.0/0 static default route toward the approved upstream next hop. If it fails, inspect show ip route 0.0.0.0, recursive next-hop reachability, upstream return routing and NAT policy. to isolate the remaining defect.
Incorrect Answers
The choice “The host resolves its gateway MAC, reaches a remote network, and traceroute shows a first-hop device on the local VLAN” concerns ipv4 host default gateway; it does not resolve the stated requirement. Show ip route displays S* 0.0.0.0/0 and an external traceroute follows the upstream, while local routes still use local interfaces.
The choice “show ip route installs the lower-AD same-prefix source, while alternative sources can remain in protocol databases without taking effect” concerns route administrative distance; it does not resolve the stated requirement. Show ip route displays S* 0.0.0.0/0 and an external traceroute follows the upstream, while local routes still use local interfaces.
The choice “show ip route and show ip ospf interface show the expected preferred path or eligible equal-cost next hops” concerns routing metrics within one protocol; it does not resolve the stated requirement. Show ip route displays S* 0.0.0.0/0 and an external traceroute follows the upstream, while local routes still use local interfaces.
Question 384
Before modifying more devices to address 'A small branch requires all otherwise-unmatched internet traffic to leave via ISP next hop 203.0.113.1.', which diagnostic evidence is most relevant?
Explanation
Correct Answer
The investigation 'Inspect show ip route 0.0.0.0, recursive next-hop reachability, upstream return routing and NAT policy.' examines the variables most likely to explain ipv4 default static route in this situation: A small branch requires all otherwise-unmatched internet traffic to leave via ISP next hop 203.0.113.1. Those checks are directly tied to the behavior that the IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred. The engineer can correlate this evidence with the expected outcome that show ip route displays S* 0.0.0.0/0 and an external traceroute follows the upstream, while local routes still use local interfaces. and decide whether to configure a reachable 0.0.0.0/0 static default route toward the approved upstream next hop.
Incorrect Answers
“Inspect ipconfig, network mask, arp -a, ping gateway, VLAN membership and the router's interface IP” pertains to ipv4 host default gateway, not the deciding condition here. The IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred.
“Inspect show ip route, show ip protocols, configured static routes and source administrative distances” pertains to route administrative distance, not the deciding condition here. The IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred.
“Inspect OSPF path costs, interface bandwidth/reference settings and the actual destination's routing entry” pertains to routing metrics within one protocol, not the deciding condition here. The IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred.
Question 385
A change board considers the issue 'A small branch requires all otherwise-unmatched internet traffic to leave via ISP next hop 203.0.113.1.'. Identify the TWO decisions that should be rejected. Select TWO answers.
Explanation
Correct Answer
“Replace every internal connected route with 0.0.0.0/0” would violate the requirement.
“Set a /32 default that matches only 0.0.0.0 rather than every unknown destination” would violate the requirement.
Incorrect Answers
“Configure a reachable 0.0.0.0/0 static default route toward the approved upstream next hop” is the controlled implementation, not an unsafe workaround. Confirm that show ip route displays S* 0.0.0.0/0 and an external traceroute follows the upstream, while local routes still use local interfaces.
“Confirm the repair by checking that show ip route displays S* 0.0.0.0/0 and an external traceroute follows the upstream, while local routes still use local interfaces” adds a relevant safeguard or verification step rather than weakening the solution.
“Collect targeted evidence to inspect show ip route 0.0.0.0, recursive next-hop reachability, upstream return routing and NAT policy” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that show ip route displays S* 0.0.0.0/0 and an external traceroute follows the upstream, while local routes still use local interfaces.
Question 386
A network operator receives this ticket: An edge router knows internal subnets but has no route to arbitrary public destinations over its uplink. Which configuration is best suited to the reported issue?
Explanation
Correct Answer
Configure a reachable 0.0.0.0/0 static default route toward the approved upstream next hop. The IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred.
Incorrect Answers
An edge router knows internal subnets but has no route to arbitrary public destinations over its uplink. “Replace every internal connected route with 0.0.0.0/0” does not implement the control that the facts call for. Instead, configure a reachable 0.0.0.0/0 static default route toward the approved upstream next hop.
An edge router knows internal subnets but has no route to arbitrary public destinations over its uplink. “Set a /32 default that matches only 0.0.0.0 rather than every unknown destination” does not implement the control that the facts call for. Instead, configure a reachable 0.0.0.0/0 static default route toward the approved upstream next hop.
An edge router knows internal subnets but has no route to arbitrary public destinations over its uplink. “Use an unreachable default next hop and assume every internet packet still leaves” would not meet the requirement. Instead, configure a reachable 0.0.0.0/0 static default route toward the approved upstream next hop.
Question 387
Which network-layer or protocol behavior most directly explains the result in this case: An edge router knows internal subnets but has no route to arbitrary public destinations over its uplink.
Explanation
Correct Answer
A network operator receives this ticket: An edge router knows internal subnets but has no route to arbitrary public destinations over its uplink. The IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred. Configure a reachable 0.0.0.0/0 static default route toward the approved upstream next hop.
Incorrect Answers
The choice “routing metric ranks candidate paths learned through the same protocol; OSPF path cost is based on configured interface costs, not simply hop count” concerns routing metrics within one protocol; it does not resolve the stated requirement. The IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred.
An edge router knows internal subnets but has no route to arbitrary public destinations over its uplink. The choice “a host ARPs for its on-link default gateway to send off-subnet packets; a gateway outside the local prefix cannot normally be resolved directly” concerns ipv4 host default gateway; it does not resolve the stated requirement. The IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred.
An edge router knows internal subnets but has no route to arbitrary public destinations over its uplink. The choice “administrative distance expresses a routing information source's trustworthiness; Cisco connected AD 0, static AD 1 and OSPF AD 110 by default” concerns route administrative distance; it does not resolve the stated requirement. The IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred.
Question 388
After correcting 'An edge router knows internal subnets but has no route to arbitrary public destinations over its uplink.', which observation is the strongest evidence that the specific requirement is met?
Explanation
Correct Answer
Because a network operator receives this ticket: An edge router knows internal subnets but has no route to arbitrary public destinations over its uplink, the IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred. Configure a reachable 0.0.0.0/0 static default route toward the approved upstream next hop.
Incorrect Answers
“Show ip route and show ip ospf interface show the expected preferred path or eligible equal-cost next hops” pertains to routing metrics within one protocol, not the deciding condition here. The IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred.
“Show ip route installs the lower-AD same-prefix source, while alternative sources can remain in protocol databases without taking effect” pertains to route administrative distance, not the deciding condition here. The IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred.
“The host resolves its gateway MAC, reaches a remote network, and traceroute shows a first-hop device on the local VLAN” pertains to ipv4 host default gateway, not the deciding condition here. The IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred.
Question 389
An operator is triaging the issue 'An edge router knows internal subnets but has no route to arbitrary public destinations over its uplink.'. What should be inspected to isolate the actual cause?
Explanation
Correct Answer
Inspect show ip route 0.0.0.0, recursive next-hop reachability, upstream return routing and NAT policy. The IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred.
Incorrect Answers
“Inspect OSPF path costs, interface bandwidth/reference settings and the actual destination's routing entry” pertains to routing metrics within one protocol, not the deciding condition here. Inspect show ip route 0.0.0.0, recursive next-hop reachability, upstream return routing and NAT policy.
“Inspect show ip route, show ip protocols, configured static routes and source administrative distances” pertains to route administrative distance, not the deciding condition here. Inspect show ip route 0.0.0.0, recursive next-hop reachability, upstream return routing and NAT policy.
“Inspect ipconfig, network mask, arp -a, ping gateway, VLAN membership and the router's interface IP” pertains to ipv4 host default gateway, not the deciding condition here. Inspect show ip route 0.0.0.0, recursive next-hop reachability, upstream return routing and NAT policy.
Question 390
For this incident: An edge router knows internal subnets but has no route to arbitrary public destinations over its uplink. Which TWO practices introduce avoidable network risk? Select TWO answers.
Explanation
Correct Answer
An edge router knows internal subnets but has no route to arbitrary public destinations over its uplink. “Replace every internal connected route with 0.0.0.0/0” would violate the requirement.
An edge router knows internal subnets but has no route to arbitrary public destinations over its uplink. “Set a /32 default that matches only 0.0.0.0 rather than every unknown destination” would violate the requirement.
Incorrect Answers
An edge router knows internal subnets but has no route to arbitrary public destinations over its uplink. “confirm the repair by checking that show ip route displays S* 0.0.0.0/0 and an external traceroute follows the upstream, while local routes still use local interfaces” adds a relevant safeguard or verification step rather than weakening the solution.
“configure a reachable 0.0.0.0/0 static default route toward the approved upstream next hop” is the controlled implementation, not an unsafe workaround. An important verification is that the IPv4 default route is a catch-all for destinations with no longer matching route; specific internal prefixes remain preferred.
“collect targeted evidence to inspect show ip route 0.0.0.0, recursive next-hop reachability, upstream return routing and NAT policy” adds a relevant safeguard or verification step rather than weakening the solution.
Cisco Certified Network Associate (CCNA) (200-301) Practice Tests
- Cisco 200-301 Practice Test 37 - 10 Questions (Last Reviewed 12-Oct-2026)
- Cisco 200-301 Practice Test 38 - 10 Questions (Last Reviewed 11-Oct-2026)
- Cisco 200-301 Practice Test 39 - 10 Questions (Last Reviewed 10-Oct-2026)
- Cisco 200-301 Practice Test 40 - 10 Questions (Last Reviewed 09-Oct-2026)
- Cisco 200-301 Practice Test 41 - 10 Questions (Last Reviewed 08-Oct-2026)
