Pass Cisco 200-301 Exam in First Attempt Guaranteed!
Get 100% Latest Exam Questions, Accurate & Verified Answers!
30 Days Free Updates, Instant Download!
Cisco 200-301 Practice Test 22
Question 210
For this incident: A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled. Which TWO practices introduce avoidable network risk? Select TWO answers.
Explanation
Correct Answer
A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled. “Assume SVIs route between VLANs on an L2-only device without ip routing” would violate the requirement.
“Delete the gateway address from each SVI while expecting inter-VLAN forwarding” would violate the requirement.
Incorrect Answers
A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled. “collect targeted evidence to inspect show ip interface brief, show vlan brief, ip routing setting and ACLs on both SVIs” adds a relevant safeguard or verification step rather than weakening the solution.
“confirm the repair by checking that show ip route lists both connected SVI networks and hosts successfully reach the opposite VLAN via their gateway” adds a relevant safeguard or verification step rather than weakening the solution.
A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled. “enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses” is the controlled implementation, not an unsafe workaround.
Question 211
An engineer must resolve the following situation: A network team bundles two distribution uplinks using open-standard negotiation and wants graceful detection if members fail. Select the most appropriate solution.
Explanation
Correct Answer
The action 'Use LACP active on at least one peer and compatible channel-group settings and link characteristics.' directly addresses the lacp active/passive etherchannel requirement in this situation: A network team bundles two distribution uplinks using open-standard negotiation and wants graceful detection if members fail. The relevant network mechanism is that lACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. A successful change should show that show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members. To distinguish a genuine correction from a superficial change, inspect show etherchannel summary, show lacp neighbor, VLAN/mode/speed settings and errdisabled member state.
Incorrect Answers
“Configure a static on-mode channel only on one end against an LACP peer” does not implement the control that the facts call for. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. Instead, use LACP active on at least one peer and compatible channel-group settings and link characteristics.
“Set both ends to passive and assume LACP initiates automatically” would not meet the requirement. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. Instead, use LACP active on at least one peer and compatible channel-group settings and link characteristics.
“Bundle ports with different trunk allowed VLAN lists and rely on LACP to fix mismatch” does not implement the control that the facts call for. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. Instead, use LACP active on at least one peer and compatible channel-group settings and link characteristics.
Question 212
For the condition 'A network team bundles two distribution uplinks using open-standard negotiation and wants graceful detection if members fail.' which networking principle best explains the correct solution?
Explanation
Correct Answer
Because a network team bundles two distribution uplinks using open-standard negotiation and wants graceful detection if members fail. Select the most appropriate solution, lACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. Use LACP active on at least one peer and compatible channel-group settings and link characteristics. Show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members.
Incorrect Answers
A network team bundles two distribution uplinks using open-standard negotiation and wants graceful detection if members fail. Select the most appropriate solution. “802.1Q tags distinguish VLAN traffic over one physical trunk; the allowed VLAN list filters which tagged VLANs traverse it” does not fully explain the decisive technical boundary in this case. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. The implementation must use LACP active on at least one peer and compatible channel-group settings and link characteristics.
The choice “On an 802.1Q trunk, normally untagged frames map to the configured native VLAN; a mismatch can misclassify traffic or create leakage” concerns native vlan mismatch; it does not resolve the stated requirement. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership.
“Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN” pertains to inter-vlan router-on-a-stick, not the deciding condition here. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. The implementation must use LACP active on at least one peer and compatible channel-group settings and link characteristics.
Question 213
For this situation: A network team bundles two distribution uplinks using open-standard negotiation and wants graceful detection if members fail. Which test would prove the configuration is behaving as intended?
Explanation
Correct Answer
The observation 'show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members.' specifically demonstrates a successful outcome for lacp active/passive etherchannel in this case: A network team bundles two distribution uplinks using open-standard negotiation and wants graceful detection if members fail. That observation tests the underlying mechanism that lACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. It is stronger evidence than a healthy unrelated service because it exercises the path affected by the remedy to use LACP active on at least one peer and compatible channel-group settings and link characteristics. If it fails, inspect show etherchannel summary, show lacp neighbor, VLAN/mode/speed settings and errdisabled member state. to isolate the remaining defect.
Incorrect Answers
“The switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets” pertains to inter-vlan router-on-a-stick, not the deciding condition here. Show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership.
“Both ends report matching native VLAN settings and no mismatch warning, and untagged test traffic remains in the intended VLAN” pertains to native vlan mismatch, not the deciding condition here. Show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership.
Because a network team bundles two distribution uplinks using open-standard negotiation and wants graceful detection if members fail. Select the most appropriate solution, “show interfaces trunk lists the required VLAN as allowed and forwarding; same-VLAN hosts on opposite switches exchange frames” alone does not establish all the required behavior. Show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership.
Question 214
Which inspection best distinguishes the problem mechanism in this incident: A network team bundles two distribution uplinks using open-standard negotiation and wants graceful detection if members fail.
Explanation
Correct Answer
The investigation 'Inspect show etherchannel summary, show lacp neighbor, VLAN/mode/speed settings and errdisabled member state.' examines the variables most likely to explain lacp active/passive etherchannel in this situation: A network team bundles two distribution uplinks using open-standard negotiation and wants graceful detection if members fail. Those checks are directly tied to the behavior that lACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. The engineer can correlate this evidence with the expected outcome that show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members. and decide whether to use LACP active on at least one peer and compatible channel-group settings and link characteristics.
Incorrect Answers
“Compare show interfaces switchport and show interfaces trunk on both peers and CDP native-VLAN warnings” pertains to native vlan mismatch, not the deciding condition here. Inspect show etherchannel summary, show lacp neighbor, VLAN/mode/speed settings and errdisabled member state. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership.
“Inspect show interfaces trunk, allowed VLAN lists, operational mode, VLAN existence and STP forwarding state” would not be the most direct first check for this failure. Inspect show etherchannel summary, show lacp neighbor, VLAN/mode/speed settings and errdisabled member state.
The choice “Inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces” concerns inter-vlan router-on-a-stick; it does not resolve the stated requirement. Inspect show etherchannel summary, show lacp neighbor, VLAN/mode/speed settings and errdisabled member state.
Question 215
Two bad design choices are hidden in this change plan: A network team bundles two distribution uplinks using open-standard negotiation and wants graceful detection if members fail. Which TWO should not be approved? Select TWO answers.
Explanation
Correct Answer
“Set both ends to passive and assume LACP initiates automatically” would violate the requirement. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership.
“Bundle ports with different trunk allowed VLAN lists and rely on LACP to fix mismatch” would violate the requirement. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership.
Incorrect Answers
“Collect targeted evidence to inspect show etherchannel summary, show lacp neighbor, VLAN/mode/speed settings and errdisabled member state” adds a relevant safeguard or verification step rather than weakening the solution. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. Confirm that show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members.
“Confirm the repair by checking that show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members” adds a relevant safeguard or verification step rather than weakening the solution. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. Confirm that show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members.
“Use LACP active on at least one peer and compatible channel-group settings and link characteristics” is the controlled implementation, not an unsafe workaround. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. Confirm that show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members.
Question 216
On a Cisco-based network, Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms. Which change most directly solves the stated requirement?
Explanation
Correct Answer
The action 'For this switching domain, use LACP active on at least one peer and compatible channel-group settings and link characteristics.' directly addresses the lacp active/passive etherchannel requirement in this situation: Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms. The relevant network mechanism is that lACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. A successful change should show that show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members. To distinguish a genuine correction from a superficial change, inspect show etherchannel summary, show lacp neighbor, VLAN/mode/speed settings and errdisabled member state.
Incorrect Answers
On a Cisco-based network, Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms. “bundle ports with different trunk allowed VLAN lists and rely on LACP to fix mismatch” does not implement the control that the facts call for. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. Instead, use LACP active on at least one peer and compatible channel-group settings and link characteristics.
On a Cisco-based network, Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms. “Set both ends to passive and assume LACP initiates automatically” would not meet the requirement. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. Instead, use LACP active on at least one peer and compatible channel-group settings and link characteristics.
On a Cisco-based network, Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms. “configure a static on-mode channel only on one end against an LACP peer” does not implement the control that the facts call for. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. Instead, use LACP active on at least one peer and compatible channel-group settings and link characteristics.
Question 217
A team is reviewing the design for this case: Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms. What technical behavior is decisive?
Explanation
Correct Answer
Because on a Cisco-based network, Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms. Which change most directly solves the stated requirement, lACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. Use LACP active on at least one peer and compatible channel-group settings and link characteristics. Show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members.
Incorrect Answers
Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms. “Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN” pertains to inter-vlan router-on-a-stick, not the deciding condition here. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. The implementation must use LACP active on at least one peer and compatible channel-group settings and link characteristics.
“On an 802.1Q trunk, normally untagged frames map to the configured native VLAN; a mismatch can misclassify traffic or create leakage” pertains to native vlan mismatch, not the deciding condition here. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. The implementation must use LACP active on at least one peer and compatible channel-group settings and link characteristics.
“802.1Q tags distinguish VLAN traffic over one physical trunk; the allowed VLAN list filters which tagged VLANs traverse it” does not fully explain the decisive technical boundary in this case. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. The implementation must use LACP active on at least one peer and compatible channel-group settings and link characteristics.
Question 218
An engineer implements a fix for 'Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms.'. Which result would conclusively validate the intended change?
Explanation
Correct Answer
LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. Show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members.
Incorrect Answers
“Show interfaces trunk lists the required VLAN as allowed and forwarding; same-VLAN hosts on opposite switches exchange frames” alone does not establish all the required behavior. Show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership.
An engineer implements a fix for 'Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms. “The switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets” pertains to inter-vlan router-on-a-stick, not the deciding condition here. Show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership.
An engineer implements a fix for 'Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms. “Both ends report matching native VLAN settings and no mismatch warning, and untagged test traffic remains in the intended VLAN” pertains to native vlan mismatch, not the deciding condition here. Show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership.
Question 219
For the case 'Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms.', which targeted checks should be compared before a disruptive change?
Explanation
Correct Answer
Inspect show etherchannel summary, show lacp neighbor, VLAN/mode/speed settings and errdisabled member state. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership. Show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members.
Incorrect Answers
For the case 'Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms. The choice “inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces” concerns inter-vlan router-on-a-stick; it does not resolve the stated requirement. Inspect show etherchannel summary, show lacp neighbor, VLAN/mode/speed settings and errdisabled member state.
For the case 'Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms. “Inspect show interfaces trunk, allowed VLAN lists, operational mode, VLAN existence and STP forwarding state” would not be the most direct first check for this failure. Inspect show etherchannel summary, show lacp neighbor, VLAN/mode/speed settings and errdisabled member state.
The choice “compare show interfaces switchport and show interfaces trunk on both peers and CDP native-VLAN warnings” concerns native vlan mismatch; it does not resolve the stated requirement. Inspect show etherchannel summary, show lacp neighbor, VLAN/mode/speed settings and errdisabled member state.
Question 220
Network review: Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms. Which TWO proposed shortcuts would be unsafe in this situation? Select TWO answers.
Explanation
Correct Answer
Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms. “Set both ends to passive and assume LACP initiates automatically” would violate the requirement. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership.
Two switches have member ports with matching characteristics, but both ends use LACP passive and the bundle never forms. “Bundle ports with different trunk allowed VLAN lists and rely on LACP to fix mismatch” would violate the requirement. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership.
Incorrect Answers
“confirm the repair by checking that show etherchannel summary reports the Port-channel bundled and member ports marked P, with throughput using expected members” adds a relevant safeguard or verification step rather than weakening the solution. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership.
“use LACP active on at least one peer and compatible channel-group settings and link characteristics” is the controlled implementation, not an unsafe workaround. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership.
“collect targeted evidence to inspect show etherchannel summary, show lacp neighbor, VLAN/mode/speed settings and errdisabled member state” adds a relevant safeguard or verification step rather than weakening the solution. LACP actively negotiates link aggregation; passive-passive does not initiate a bundle and mismatched attributes prevent stable membership.
Cisco Certified Network Associate (CCNA) (200-301) Practice Tests
- Cisco 200-301 Practice Test 20 - 10 Questions (Last Reviewed 29-Oct-2026)
- Cisco 200-301 Practice Test 21 - 10 Questions (Last Reviewed 28-Oct-2026)
- Cisco 200-301 Practice Test 22 - 10 Questions (Last Reviewed 27-Oct-2026)
- Cisco 200-301 Practice Test 23 - 10 Questions (Last Reviewed 26-Oct-2026)
- Cisco 200-301 Practice Test 24 - 10 Questions (Last Reviewed 25-Oct-2026)
