Cisco 200-301 Practice Test 20 - Prepaway
Practice Exams:

Pass Cisco 200-301 Exam in First Attempt Guaranteed!

Get 100% Latest Exam Questions, Accurate & Verified Answers!

30 Days Free Updates, Instant Download!

Verified By Experts
Premium Bundle
$29.98
$79.99 $109.97

200-301 Premium Bundle


  • Premium File 760 Questions & Answers. Last update: Nov 10, 2026
  • Training Course 271 Lectures
  • Study Guide 1969 Pages

Cisco 200-301 Practice Test 20

Question 190

For this incident: A branch has untagged management frames classified into different VLANs on opposite ends of an 802.1Q trunk. Which TWO practices introduce avoidable network risk? Select TWO answers.

  1. For this switching domain, set an identical designated native VLAN on both trunk ends and keep user traffic explicitly tagged where possible.
  2. For this switching domain, change only the allowed VLAN list while leaving native VLAN settings different.
  3. For this switching domain, collect targeted evidence to compare show interfaces switchport and show interfaces trunk on both peers and CDP native-VLAN warnings.
  4. For this switching domain, confirm the repair by checking that both ends report matching native VLAN settings and no mismatch warning, and untagged test traffic remains in the intended VLAN.
  5. For this switching domain, treat native VLAN mismatch as an IP route metric problem.

Explanation

Correct Answer

B:

“Change only the allowed VLAN list while leaving native VLAN settings different” would violate the requirement. The appropriate control instead is to set an identical designated native VLAN on both trunk ends and keep user traffic explicitly tagged where possible.

E:

“Treat native VLAN mismatch as an IP route metric problem” would violate the requirement. The appropriate control instead is to set an identical designated native VLAN on both trunk ends and keep user traffic explicitly tagged where possible.

Incorrect Answers

A:

“set an identical designated native VLAN on both trunk ends and keep user traffic explicitly tagged where possible” is the controlled implementation, not an unsafe workaround. Confirm that on an 802.1Q trunk, normally untagged frames map to the configured native VLAN; a mismatch can misclassify traffic or create leakage.

C:

“collect targeted evidence to compare show interfaces switchport and show interfaces trunk on both peers and CDP native-VLAN warnings” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that on an 802.1Q trunk, normally untagged frames map to the configured native VLAN; a mismatch can misclassify traffic or create leakage.

D:

“confirm the repair by checking that both ends report matching native VLAN settings and no mismatch warning, and untagged test traffic remains in the intended VLAN” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that on an 802.1Q trunk, normally untagged frames map to the configured native VLAN; a mismatch can misclassify traffic or create leakage.

Question 191

An engineer must resolve the following situation: A branch has VLANs 10 and 20 on a Layer 2 switch and one router interface for both networks. Select the most appropriate solution.

  1. Assign one untagged IPv4 address to the switch trunk and expect it to route every VLAN.
  2. Set identical IP subnets on both VLAN subinterfaces to avoid routing.
  3. Create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch.
  4. Create VLANs but omit routed default gateways for all hosts.

Explanation

Correct Answer

C:

The action 'Create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch.' directly addresses the inter-vlan router-on-a-stick requirement in this situation: A branch has VLANs 10 and 20 on a Layer 2 switch and one router interface for both networks. The relevant network mechanism is that router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. A successful change should show that the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets. To distinguish a genuine correction from a superficial change, inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces.

Incorrect Answers

A:

“Assign one untagged IPv4 address to the switch trunk and expect it to route every VLAN” does not implement the control that the facts call for. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. Instead, create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch.

B:

“Set identical IP subnets on both VLAN subinterfaces to avoid routing” does not implement the control that the facts call for. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. Instead, create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch.

D:

“Create VLANs but omit routed default gateways for all hosts” would not meet the requirement. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. Instead, create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch.

Question 192

For the condition 'A branch has VLANs 10 and 20 on a Layer 2 switch and one router interface for both networks.' which networking principle best explains the correct solution?

  1. PortFast lets an edge port enter forwarding without standard listening/learning delays; BPDU Guard errdisables the port upon receiving a BPDU.
  2. Non-root switches select their root port based on the best received BPDU and lowest cumulative path cost to the root bridge.
  3. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.
  4. The root bridge is selected by the lowest bridge ID, consisting of priority and MAC address; equal priorities break ties by MAC.

Explanation

Correct Answer

C:

A branch has VLANs 10 and 20 on a Layer 2 switch and one router interface for both networks. Select the most appropriate solution. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. Create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch.

Incorrect Answers

A:

“PortFast lets an edge port enter forwarding without standard listening/learning delays; BPDU Guard errdisables the port upon receiving a BPDU” does not fully explain the decisive technical boundary in this case. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

B:

The choice “Non-root switches select their root port based on the best received BPDU and lowest cumulative path cost to the root bridge” concerns stp root port path cost; it does not resolve the stated requirement. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

D:

The choice “The root bridge is selected by the lowest bridge ID, consisting of priority and MAC address; equal priorities break ties by MAC” concerns rapid pvst root bridge priority; it does not resolve the stated requirement. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

Question 193

For this situation: A branch has VLANs 10 and 20 on a Layer 2 switch and one router interface for both networks. Which test would prove the configuration is behaving as intended?

  1. The switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets.
  2. A normal host port forwards promptly; a test BPDU triggers errdisable and syslog rather than permitting an unauthorized loop.
  3. show spanning-tree vlan 30 reports the intended root ID at distribution, and access switches have root ports pointing toward it.
  4. show spanning-tree shows the intended root port forwarding and redundant alternatives in an appropriate discarding role.

Explanation

Correct Answer

A:

Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. The switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets. If this test fails, inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces.

Incorrect Answers

B:

“A normal host port forwards promptly; a test BPDU triggers errdisable and syslog rather than permitting an unauthorized loop” alone does not establish all the required behavior. The switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

C:

The choice “show spanning-tree vlan 30 reports the intended root ID at distribution, and access switches have root ports pointing toward it” concerns rapid pvst root bridge priority; it does not resolve the stated requirement. The switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets.

D:

The choice “show spanning-tree shows the intended root port forwarding and redundant alternatives in an appropriate discarding role” concerns stp root port path cost; it does not resolve the stated requirement. The switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets.

Question 194

Which inspection best distinguishes the problem mechanism in this incident: A branch has VLANs 10 and 20 on a Layer 2 switch and one router interface for both networks.

  1. Inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces.
  2. Compare bridge priority, bridge MAC, root ID and port roles in show spanning-tree vlan 30 across switches.
  3. Compare root-path cost and received BPDU priorities per candidate interface, rather than only local interface names.
  4. Inspect show spanning-tree interface detail, show interfaces status err-disabled and BPDU Guard logs.

Explanation

Correct Answer

A:

The investigation 'Inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces.' examines the variables most likely to explain inter-vlan router-on-a-stick in this situation: A branch has VLANs 10 and 20 on a Layer 2 switch and one router interface for both networks. Those checks are directly tied to the behavior that router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. The engineer can correlate this evidence with the expected outcome that the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets. and decide whether to create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch.

Incorrect Answers

B:

The choice “Compare bridge priority, bridge MAC, root ID and port roles in show spanning-tree vlan 30 across switches” concerns rapid pvst root bridge priority; it does not resolve the stated requirement. Inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces.

C:

“Compare root-path cost and received BPDU priorities per candidate interface, rather than only local interface names” pertains to stp root port path cost, not the deciding condition here. Inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

D:

“Inspect show spanning-tree interface detail, show interfaces status err-disabled and BPDU Guard logs” would not be the most direct first check for this failure. Inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

Question 195

Two bad design choices are hidden in this change plan: A branch has VLANs 10 and 20 on a Layer 2 switch and one router interface for both networks. Which TWO should not be approved? Select TWO answers.

  1. Create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch.
  2. Assign one untagged IPv4 address to the switch trunk and expect it to route every VLAN.
  3. Collect targeted evidence to inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces.
  4. Confirm the repair by checking that the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets.
  5. Create VLANs but omit routed default gateways for all hosts.

Explanation

Correct Answer

B:

“Assign one untagged IPv4 address to the switch trunk and expect it to route every VLAN” would violate the requirement. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

E:

“Create VLANs but omit routed default gateways for all hosts” would violate the requirement. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

Incorrect Answers

A:

“Create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch” is the controlled implementation, not an unsafe workaround. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. Confirm that the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets.

C:

“Collect targeted evidence to inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces” adds a relevant safeguard or verification step rather than weakening the solution. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

D:

“Confirm the repair by checking that the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets” adds a relevant safeguard or verification step rather than weakening the solution. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

Question 196

On a Cisco-based network, A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. Which change most directly solves the stated requirement?

  1. For this switching domain, create VLANs but omit routed default gateways for all hosts.
  2. For this switching domain, create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch.
  3. For this switching domain, set identical IP subnets on both VLAN subinterfaces to avoid routing.
  4. For this switching domain, assign one untagged IPv4 address to the switch trunk and expect it to route every VLAN.

Explanation

Correct Answer

B:

The action 'For this switching domain, create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch.' directly addresses the inter-vlan router-on-a-stick requirement in this situation: A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. The relevant network mechanism is that router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. A successful change should show that the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets. To distinguish a genuine correction from a superficial change, inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces.

Incorrect Answers

A:

On a Cisco-based network, A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. “Create VLANs but omit routed default gateways for all hosts” would not meet the requirement. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. Instead, create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch.

C:

On a Cisco-based network, A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. “set identical IP subnets on both VLAN subinterfaces to avoid routing” does not implement the control that the facts call for. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. Instead, create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch.

D:

On a Cisco-based network, A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. “assign one untagged IPv4 address to the switch trunk and expect it to route every VLAN” does not implement the control that the facts call for. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. Instead, create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch.

Question 197

A team is reviewing the design for this case: A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. What technical behavior is decisive?

  1. For this switching domain, non-root switches select their root port based on the best received BPDU and lowest cumulative path cost to the root bridge.
  2. For this switching domain, router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.
  3. For this switching domain, the root bridge is selected by the lowest bridge ID, consisting of priority and MAC address; equal priorities break ties by MAC.
  4. For this switching domain, portFast lets an edge port enter forwarding without standard listening/learning delays; BPDU Guard errdisables the port upon receiving a BPDU.

Explanation

Correct Answer

B:

On a Cisco-based network, A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. Which change most directly solves the stated requirement. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. Create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch.

Incorrect Answers

A:

A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. The choice “non-root switches select their root port based on the best received BPDU and lowest cumulative path cost to the root bridge” concerns stp root port path cost; it does not resolve the stated requirement. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

C:

A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. The choice “the root bridge is selected by the lowest bridge ID, consisting of priority and MAC address; equal priorities break ties by MAC” concerns rapid pvst root bridge priority; it does not resolve the stated requirement. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

D:

A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. “PortFast lets an edge port enter forwarding without standard listening/learning delays; BPDU Guard errdisables the port upon receiving a BPDU” does not fully explain the decisive technical boundary in this case. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

Question 198

An engineer implements a fix for 'A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway.'. Which result would conclusively validate the intended change?

  1. For this switching domain, show spanning-tree shows the intended root port forwarding and redundant alternatives in an appropriate discarding role.
  2. For this switching domain, the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets.
  3. For this switching domain, a normal host port forwards promptly; a test BPDU triggers errdisable and syslog rather than permitting an unauthorized loop.
  4. For this switching domain, show spanning-tree vlan 30 reports the intended root ID at distribution, and access switches have root ports pointing toward it.

Explanation

Correct Answer

B:

Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. The switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets.

Incorrect Answers

A:

“Show spanning-tree shows the intended root port forwarding and redundant alternatives in an appropriate discarding role” pertains to stp root port path cost, not the deciding condition here. The switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

C:

An engineer implements a fix for 'A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. “A normal host port forwards promptly; a test BPDU triggers errdisable and syslog rather than permitting an unauthorized loop” alone does not establish all the required behavior. The switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

D:

“Show spanning-tree vlan 30 reports the intended root ID at distribution, and access switches have root ports pointing toward it” pertains to rapid pvst root bridge priority, not the deciding condition here. The switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

Question 199

For the case 'A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway.', which targeted checks should be compared before a disruptive change?

  1. For this switching domain, compare bridge priority, bridge MAC, root ID and port roles in show spanning-tree vlan 30 across switches.
  2. For this switching domain, inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces.
  3. For this switching domain, inspect show spanning-tree interface detail, show interfaces status err-disabled and BPDU Guard logs.
  4. For this switching domain, compare root-path cost and received BPDU priorities per candidate interface, rather than only local interface names.

Explanation

Correct Answer

B:

Inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. The switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets.

Incorrect Answers

A:

For the case 'A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. The choice “compare bridge priority, bridge MAC, root ID and port roles in show spanning-tree vlan 30 across switches” concerns rapid pvst root bridge priority; it does not resolve the stated requirement. Inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces.

C:

“Inspect show spanning-tree interface detail, show interfaces status err-disabled and BPDU Guard logs” would not be the most direct first check for this failure. Inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces.

D:

The choice “compare root-path cost and received BPDU priorities per candidate interface, rather than only local interface names” concerns stp root port path cost; it does not resolve the stated requirement. Inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces.

Question 200

Network review: A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. Which TWO proposed shortcuts would be unsafe in this situation? Select TWO answers.

  1. For this switching domain, assign one untagged IPv4 address to the switch trunk and expect it to route every VLAN.
  2. For this switching domain, create VLANs but omit routed default gateways for all hosts.
  3. For this switching domain, confirm the repair by checking that the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets.
  4. For this switching domain, create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch.
  5. For this switching domain, collect targeted evidence to inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces.

Explanation

Correct Answer

A:

A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. “Assign one untagged IPv4 address to the switch trunk and expect it to route every VLAN” would violate the requirement. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

B:

A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. “Create VLANs but omit routed default gateways for all hosts” would violate the requirement. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

Incorrect Answers

C:

“confirm the repair by checking that the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets” adds a relevant safeguard or verification step rather than weakening the solution. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. Confirm that the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets.

D:

A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. “create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch” is the controlled implementation, not an unsafe workaround. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. Confirm that the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets.

E:

“collect targeted evidence to inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces” adds a relevant safeguard or verification step rather than weakening the solution. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. Confirm that the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets.

Cisco Certified Network Associate (CCNA) (200-301) Practice Tests