Cisco 200-301 Practice Test 21 - Prepaway
Practice Exams:

Pass Cisco 200-301 Exam in First Attempt Guaranteed!

Get 100% Latest Exam Questions, Accurate & Verified Answers!

30 Days Free Updates, Instant Download!

Verified By Experts
Premium Bundle
$29.98
$79.99 $109.97

200-301 Premium Bundle


  • Premium File 760 Questions & Answers. Last update: Nov 10, 2026
  • Training Course 271 Lectures
  • Study Guide 1969 Pages

Cisco 200-301 Practice Test 21

Question 200

Network review: A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. Which TWO proposed shortcuts would be unsafe in this situation? Select TWO answers.

  1. For this switching domain, assign one untagged IPv4 address to the switch trunk and expect it to route every VLAN.
  2. For this switching domain, create VLANs but omit routed default gateways for all hosts.
  3. For this switching domain, confirm the repair by checking that the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets.
  4. For this switching domain, create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch.
  5. For this switching domain, collect targeted evidence to inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces.

Explanation

Correct Answer

A:

A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. “Assign one untagged IPv4 address to the switch trunk and expect it to route every VLAN” would violate the requirement. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

B:

A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. “Create VLANs but omit routed default gateways for all hosts” would violate the requirement. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN.

Incorrect Answers

C:

“confirm the repair by checking that the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets” adds a relevant safeguard or verification step rather than weakening the solution. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. Confirm that the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets.

D:

A small lab runs two VLANs over Gi0/1 to an external router but neither VLAN has its subinterface gateway. “create per-VLAN routed subinterfaces using encapsulation dot1Q and a matching trunk to the switch” is the controlled implementation, not an unsafe workaround. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. Confirm that the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets.

E:

“collect targeted evidence to inspect show interfaces trunk, show ip interface brief and show running-config interface on the router subinterfaces” adds a relevant safeguard or verification step rather than weakening the solution. Router-on-a-stick uses one physical router link with 802.1Q subinterfaces, each acting as a Layer 3 gateway for a VLAN. Confirm that the switch uplink is a trunk, each router subinterface is up with matching encapsulation and hosts route between subnets.

Question 201

Consider this operational failure: Two campus VLANs have correct SVIs on a multilayer switch but devices cannot communicate between VLANs. What should the administrator implement first?

  1. Enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses.
  2. Put both SVIs into the same IP prefix and ignore duplicate addressing.
  3. Delete the gateway address from each SVI while expecting inter-VLAN forwarding.
  4. Assume SVIs route between VLANs on an L2-only device without ip routing.

Explanation

Correct Answer

A:

The action 'Enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses.' directly addresses the layer 3 svi routing requirement in this situation: Two campus VLANs have correct SVIs on a multilayer switch but devices cannot communicate between VLANs. The relevant network mechanism is that an SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN. A successful change should show that show ip route lists both connected SVI networks and hosts successfully reach the opposite VLAN via their gateway. To distinguish a genuine correction from a superficial change, inspect show ip interface brief, show vlan brief, ip routing setting and ACLs on both SVIs.

Incorrect Answers

B:

“Put both SVIs into the same IP prefix and ignore duplicate addressing” would not meet the requirement. Instead, enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses.

C:

“Delete the gateway address from each SVI while expecting inter-VLAN forwarding” does not implement the control that the facts call for. Instead, enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses.

D:

“Assume SVIs route between VLANs on an L2-only device without ip routing” would not meet the requirement. Instead, enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses.

Question 202

While troubleshooting 'Two campus VLANs have correct SVIs on a multilayer switch but devices cannot communicate between VLANs.', which underlying protocol rule should guide the decision?

  1. An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN.
  2. CDP and LLDP advertise directly connected device and port identity at Layer 2; they do not discover every routed hop.
  3. Enterprise WLAN security uses per-user 802.1X/EAP authentication against an AAA server; PSK shares a common secret among clients.
  4. A WLAN SSID is associated with security and policy settings, including the client VLAN; the RF beacon alone does not establish correct data-path mapping.

Explanation

Correct Answer

A:

An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN. Show ip route lists both connected SVI networks and hosts successfully reach the opposite VLAN via their gateway.

Incorrect Answers

B:

“CDP and LLDP advertise directly connected device and port identity at Layer 2; they do not discover every routed hop” would not meet the requirement. An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN.

C:

“Enterprise WLAN security uses per-user 802.1X/EAP authentication against an AAA server; PSK shares a common secret among clients” pertains to wlan wpa2 enterprise 802, not the deciding condition here. An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN.

D:

“A WLAN SSID is associated with security and policy settings, including the client VLAN; the RF beacon alone does not establish correct data-path mapping” would not be the most direct first check for this failure. An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN.

Question 203

Which measurable result should be checked before closing this ticket: Two campus VLANs have correct SVIs on a multilayer switch but devices cannot communicate between VLANs.

  1. The associated client receives an address from the corporate VLAN and can access only authorized services; WLC client details show intended policy.
  2. A valid identity joins the SSID and obtains the authorized VLAN, while a revoked account fails with a traceable AAA result.
  3. show ip route lists both connected SVI networks and hosts successfully reach the opposite VLAN via their gateway.
  4. Neighbor output maps local ports to expected device IDs and remote port IDs, matching physically traced cabling.

Explanation

Correct Answer

C:

Show ip route lists both connected SVI networks and hosts successfully reach the opposite VLAN via their gateway. Enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses.

Incorrect Answers

A:

The choice “The associated client receives an address from the corporate VLAN and can access only authorized services; WLC client details show intended policy” concerns wlc ssid to vlan; it does not resolve the stated requirement. Show ip route lists both connected SVI networks and hosts successfully reach the opposite VLAN via their gateway.

B:

The choice “A valid identity joins the SSID and obtains the authorized VLAN, while a revoked account fails with a traceable AAA result” concerns wlan wpa2 enterprise 802; it does not resolve the stated requirement. Show ip route lists both connected SVI networks and hosts successfully reach the opposite VLAN via their gateway.

D:

“Neighbor output maps local ports to expected device IDs and remote port IDs, matching physically traced cabling” alone does not establish all the required behavior. Show ip route lists both connected SVI networks and hosts successfully reach the opposite VLAN via their gateway.

Question 204

Before modifying more devices to address 'Two campus VLANs have correct SVIs on a multilayer switch but devices cannot communicate between VLANs.', which diagnostic evidence is most relevant?

  1. Inspect show cdp neighbors detail or show lldp neighbors detail and verify discovery is enabled on both endpoints.
  2. Inspect WLC AAA server reachability, RADIUS replies, EAP method, client association and policy VLAN.
  3. Inspect WLC WLAN and policy profile mappings, client VLAN, SSID state, DHCP relay and access-interface trunk.
  4. Inspect show ip interface brief, show vlan brief, ip routing setting and ACLs on both SVIs.

Explanation

Correct Answer

D:

The investigation 'Inspect show ip interface brief, show vlan brief, ip routing setting and ACLs on both SVIs.' examines the variables most likely to explain layer 3 svi routing in this situation: Two campus VLANs have correct SVIs on a multilayer switch but devices cannot communicate between VLANs. Those checks are directly tied to the behavior that an SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN. The engineer can correlate this evidence with the expected outcome that show ip route lists both connected SVI networks and hosts successfully reach the opposite VLAN via their gateway. and decide whether to enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses.

Incorrect Answers

A:

“Inspect show cdp neighbors detail or show lldp neighbors detail and verify discovery is enabled on both endpoints” would not be the most direct first check for this failure. An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN.

B:

“Inspect WLC AAA server reachability, RADIUS replies, EAP method, client association and policy VLAN” pertains to wlan wpa2 enterprise 802, not the deciding condition here. An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN.

C:

“Inspect WLC WLAN and policy profile mappings, client VLAN, SSID state, DHCP relay and access-interface trunk” pertains to wlc ssid to vlan, not the deciding condition here. An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN.

Question 205

A change board considers the issue 'Two campus VLANs have correct SVIs on a multilayer switch but devices cannot communicate between VLANs.'. Identify the TWO decisions that should be rejected. Select TWO answers.

  1. Assume SVIs route between VLANs on an L2-only device without ip routing.
  2. Collect targeted evidence to inspect show ip interface brief, show vlan brief, ip routing setting and ACLs on both SVIs.
  3. Delete the gateway address from each SVI while expecting inter-VLAN forwarding.
  4. Confirm the repair by checking that show ip route lists both connected SVI networks and hosts successfully reach the opposite VLAN via their gateway.
  5. Enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses.

Explanation

Correct Answer

A:

“Assume SVIs route between VLANs on an L2-only device without ip routing” would violate the requirement.

C:

“Delete the gateway address from each SVI while expecting inter-VLAN forwarding” would violate the requirement. The appropriate control instead is to enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses.

Incorrect Answers

B:

“Collect targeted evidence to inspect show ip interface brief, show vlan brief, ip routing setting and ACLs on both SVIs” adds a relevant safeguard or verification step rather than weakening the solution.

D:

“Confirm the repair by checking that show ip route lists both connected SVI networks and hosts successfully reach the opposite VLAN via their gateway” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that show ip route lists both connected SVI networks and hosts successfully reach the opposite VLAN via their gateway.

E:

“Enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses” is the controlled implementation, not an unsafe workaround.

Question 206

A network operator receives this ticket: A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled. Which configuration is best suited to the reported issue?

  1. For this switching domain, enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses.
  2. For this switching domain, assume SVIs route between VLANs on an L2-only device without ip routing.
  3. For this switching domain, delete the gateway address from each SVI while expecting inter-VLAN forwarding.
  4. For this switching domain, put both SVIs into the same IP prefix and ignore duplicate addressing.

Explanation

Correct Answer

A:

The action 'For this switching domain, enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses.' directly addresses the layer 3 svi routing requirement in this situation: A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled. The relevant network mechanism is that an SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN. A successful change should show that show ip route lists both connected SVI networks and hosts successfully reach the opposite VLAN via their gateway. To distinguish a genuine correction from a superficial change, inspect show ip interface brief, show vlan brief, ip routing setting and ACLs on both SVIs.

Incorrect Answers

B:

A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled. “Assume SVIs route between VLANs on an L2-only device without ip routing” would not meet the requirement. Instead, enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses.

C:

A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled. “Delete the gateway address from each SVI while expecting inter-VLAN forwarding” does not implement the control that the facts call for. Instead, enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses.

D:

A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled. “Put both SVIs into the same IP prefix and ignore duplicate addressing” would not meet the requirement. Instead, enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses.

Question 207

Which network-layer or protocol behavior most directly explains the result in this case: A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled.

  1. For this switching domain, an SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN.
  2. For this switching domain, a WLAN SSID is associated with security and policy settings, including the client VLAN; the RF beacon alone does not establish correct data-path mapping.
  3. For this switching domain, cDP and LLDP advertise directly connected device and port identity at Layer 2; they do not discover every routed hop.
  4. For this switching domain, enterprise WLAN security uses per-user 802.1X/EAP authentication against an AAA server; PSK shares a common secret among clients.

Explanation

Correct Answer

A:

An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN.

Incorrect Answers

B:

“A WLAN SSID is associated with security and policy settings, including the client VLAN; the RF beacon alone does not establish correct data-path mapping” alone does not establish all the required behavior. An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN.

C:

A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled. “CDP and LLDP advertise directly connected device and port identity at Layer 2; they do not discover every routed hop” would not meet the requirement. An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN.

D:

A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled. “Enterprise WLAN security uses per-user 802.1X/EAP authentication against an AAA server; PSK shares a common secret among clients” pertains to wlan wpa2 enterprise 802, not the deciding condition here. An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN.

Question 208

After correcting 'A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled.', which observation is the strongest evidence that the specific requirement is met?

  1. For this switching domain, a valid identity joins the SSID and obtains the authorized VLAN, while a revoked account fails with a traceable AAA result.
  2. For this switching domain, show ip route lists both connected SVI networks and hosts successfully reach the opposite VLAN via their gateway.
  3. For this switching domain, neighbor output maps local ports to expected device IDs and remote port IDs, matching physically traced cabling.
  4. For this switching domain, the associated client receives an address from the corporate VLAN and can access only authorized services; WLC client details show intended policy.

Explanation

Correct Answer

B:

An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN. If this test fails, inspect show ip interface brief, show vlan brief, ip routing setting and ACLs on both SVIs.

Incorrect Answers

A:

The choice “a valid identity joins the SSID and obtains the authorized VLAN, while a revoked account fails with a traceable AAA result” concerns wlan wpa2 enterprise 802; it does not resolve the stated requirement. An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN.

C:

“Neighbor output maps local ports to expected device IDs and remote port IDs, matching physically traced cabling” alone does not establish all the required behavior. An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN.

D:

The choice “the associated client receives an address from the corporate VLAN and can access only authorized services; WLC client details show intended policy” concerns wlc ssid to vlan; it does not resolve the stated requirement. An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN.

Question 209

An operator is triaging the issue 'A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled.'. What should be inspected to isolate the actual cause?

  1. For this switching domain, inspect show cdp neighbors detail or show lldp neighbors detail and verify discovery is enabled on both endpoints.
  2. For this switching domain, inspect WLC WLAN and policy profile mappings, client VLAN, SSID state, DHCP relay and access-interface trunk.
  3. For this switching domain, inspect show ip interface brief, show vlan brief, ip routing setting and ACLs on both SVIs.
  4. For this switching domain, inspect WLC AAA server reachability, RADIUS replies, EAP method, client association and policy VLAN.

Explanation

Correct Answer

C:

Inspect show ip interface brief, show vlan brief, ip routing setting and ACLs on both SVIs. An SVI terminates a VLAN at Layer 3; inter-VLAN packet forwarding requires the switch's routing function and active underlying VLAN.

Incorrect Answers

A:

“Inspect show cdp neighbors detail or show lldp neighbors detail and verify discovery is enabled on both endpoints” would not be the most direct first check for this failure. Inspect show ip interface brief, show vlan brief, ip routing setting and ACLs on both SVIs.

B:

“Inspect WLC WLAN and policy profile mappings, client VLAN, SSID state, DHCP relay and access-interface trunk” pertains to wlc ssid to vlan, not the deciding condition here. Inspect show ip interface brief, show vlan brief, ip routing setting and ACLs on both SVIs.

D:

“Inspect WLC AAA server reachability, RADIUS replies, EAP method, client association and policy VLAN” pertains to wlan wpa2 enterprise 802, not the deciding condition here. Inspect show ip interface brief, show vlan brief, ip routing setting and ACLs on both SVIs.

Question 210

For this incident: A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled. Which TWO practices introduce avoidable network risk? Select TWO answers.

  1. For this switching domain, collect targeted evidence to inspect show ip interface brief, show vlan brief, ip routing setting and ACLs on both SVIs.
  2. For this switching domain, confirm the repair by checking that show ip route lists both connected SVI networks and hosts successfully reach the opposite VLAN via their gateway.
  3. For this switching domain, enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses.
  4. For this switching domain, assume SVIs route between VLANs on an L2-only device without ip routing.
  5. For this switching domain, delete the gateway address from each SVI while expecting inter-VLAN forwarding.

Explanation

Correct Answer

D:

A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled. “Assume SVIs route between VLANs on an L2-only device without ip routing” would violate the requirement.

E:

“Delete the gateway address from each SVI while expecting inter-VLAN forwarding” would violate the requirement.

Incorrect Answers

A:

A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled. “collect targeted evidence to inspect show ip interface brief, show vlan brief, ip routing setting and ACLs on both SVIs” adds a relevant safeguard or verification step rather than weakening the solution.

B:

“confirm the repair by checking that show ip route lists both connected SVI networks and hosts successfully reach the opposite VLAN via their gateway” adds a relevant safeguard or verification step rather than weakening the solution.

C:

A distribution switch provides gateways VLAN 15 and 25 but ip routing has not been enabled. “enable ip routing on the multilayer switch and ensure both active VLAN SVIs have valid IP addresses” is the controlled implementation, not an unsafe workaround.

Cisco Certified Network Associate (CCNA) (200-301) Practice Tests