Pass Cisco 200-301 Exam in First Attempt Guaranteed!
Get 100% Latest Exam Questions, Accurate & Verified Answers!
30 Days Free Updates, Instant Download!
Cisco 200-301 Practice Test 16
Question 150
For this incident: A school with multiple overlapping 2.4-GHz radios needs to plan channel reuse to reduce adjacent-channel overlap. Which TWO practices introduce avoidable network risk? Select TWO answers.
Explanation
Correct Answer
“Set every nearby 2.4-GHz AP to channel 4 to maximize unique channel numbers” would violate the requirement. The appropriate control instead is to plan non-overlapping 20-MHz 2.4-GHz channels such as 1, 6 and 11 and adjust power based on site survey.
A school with multiple overlapping 2.4-GHz radios needs to plan channel reuse to reduce adjacent-channel overlap. “Increase all AP transmit power to maximum regardless of cell overlap” would violate the requirement. The appropriate control instead is to plan non-overlapping 20-MHz 2.4-GHz channels such as 1, 6 and 11 and adjust power based on site survey.
Incorrect Answers
“plan non-overlapping 20-MHz 2.4-GHz channels such as 1, 6 and 11 and adjust power based on site survey” is the controlled implementation, not an unsafe workaround. Confirm that 2.4-GHz Wi-Fi has limited non-overlapping 20-MHz channels; adjacent channels overlap and interfere when cells are close.
“confirm the repair by checking that spectrum survey shows reduced adjacent-channel overlap, stable signal quality and improved retransmission rates in the affected area” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that 2.4-GHz Wi-Fi has limited non-overlapping 20-MHz channels; adjacent channels overlap and interfere when cells are close.
“collect targeted evidence to inspect AP channel assignments, channel width, neighboring RSSI, spectrum noise and radio retry statistics” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that 2.4-GHz Wi-Fi has limited non-overlapping 20-MHz channels; adjacent channels overlap and interfere when cells are close.
Question 151
An engineer must resolve the following situation: A service provider carries tenant red and tenant blue with overlapping 10.0.0.0/24 routes on one router. Select the most appropriate solution.
Explanation
Correct Answer
The action 'Use separate VRF routing instances and bind the correct interfaces to each tenant routing table.' directly addresses the vrf and routed table isolation requirement in this situation: A service provider carries tenant red and tenant blue with overlapping 10.0.0.0/24 routes on one router. The relevant network mechanism is that vRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants. A successful change should show that show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added. To distinguish a genuine correction from a superficial change, check per-VRF interface membership, per-VRF routes, route leaking configuration and tenant-specific ping vrf.
Incorrect Answers
“Advertise all tenant routes to the global table without reviewing access policies” would not meet the requirement. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants. Instead, use separate VRF routing instances and bind the correct interfaces to each tenant routing table.
“Replace per-VRF route tables with merely different Layer 2 port descriptions” does not implement the control that the facts call for. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants. Instead, use separate VRF routing instances and bind the correct interfaces to each tenant routing table.
“Put both tenants in the same default VRF and assume overlapping prefixes remain isolated” would not meet the requirement. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants. Instead, use separate VRF routing instances and bind the correct interfaces to each tenant routing table.
Question 152
For the condition 'A service provider carries tenant red and tenant blue with overlapping 10.0.0.0/24 routes on one router.' which networking principle best explains the correct solution?
Explanation
Correct Answer
VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants. Use separate VRF routing instances and bind the correct interfaces to each tenant routing table.
Incorrect Answers
“A Layer 2 switch learns source MAC addresses on ingress ports, forwards known unicasts toward one port, and floods unknown unicast within the associated VLAN” pertains to mac learning, not the deciding condition here. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants. The implementation must use separate VRF routing instances and bind the correct interfaces to each tenant routing table.
“Controller-managed WLANs separate centralized policy and management from the radio access point's client-facing RF service” pertains to wireless ap, not the deciding condition here. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants. The implementation must use separate VRF routing instances and bind the correct interfaces to each tenant routing table.
“Collapsed-core designs combine core and distribution functions, while spine-leaf fabrics use a consistent leaf-to-spine forwarding structure and equal-cost paths” does not fully explain the decisive technical boundary in this case. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants. The implementation must use separate VRF routing instances and bind the correct interfaces to each tenant routing table.
Question 153
For this situation: A service provider carries tenant red and tenant blue with overlapping 10.0.0.0/24 routes on one router. Which test would prove the configuration is behaving as intended?
Explanation
Correct Answer
The observation 'show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added.' specifically demonstrates a successful outcome for vrf and routed table isolation in this case: A service provider carries tenant red and tenant blue with overlapping 10.0.0.0/24 routes on one router. That observation tests the underlying mechanism that vRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants. It is stronger evidence than a healthy unrelated service because it exercises the path affected by the remedy to use separate VRF routing instances and bind the correct interfaces to each tenant routing table. If it fails, check per-VRF interface membership, per-VRF routes, route leaking configuration and tenant-specific ping vrf. to isolate the remaining defect.
Incorrect Answers
The choice “The intended SSID and security policy appear consistently on joined APs, and authenticated clients roam using the same authorized WLAN” concerns wireless ap; it does not resolve the stated requirement. Show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added.
“Show mac address-table dynamic displays the learned source and its current interface; subsequent traffic reaches only the correct destination port” pertains to mac learning, not the deciding condition here. Show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants.
“Traffic follows intended redundant links with acceptable convergence, and topology diagrams show the chosen hierarchy or fabric connectivity” alone does not establish all the required behavior. Show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added.
Question 154
Which inspection best distinguishes the problem mechanism in this incident: A service provider carries tenant red and tenant blue with overlapping 10.0.0.0/24 routes on one router.
Explanation
Correct Answer
The investigation 'Check per-VRF interface membership, per-VRF routes, route leaking configuration and tenant-specific ping vrf.' examines the variables most likely to explain vrf and routed table isolation in this situation: A service provider carries tenant red and tenant blue with overlapping 10.0.0.0/24 routes on one router. Those checks are directly tied to the behavior that vRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants. The engineer can correlate this evidence with the expected outcome that show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added. and decide whether to use separate VRF routing instances and bind the correct interfaces to each tenant routing table.
Incorrect Answers
“Trace physical uplinks, check routed adjacency and ECMP entries, compare oversubscription and failure domains” would not be the most direct first check for this failure. Check per-VRF interface membership, per-VRF routes, route leaking configuration and tenant-specific ping vrf.
“Inspect AP join status, WLC WLAN profile, mapped policy profile, RF state and client association details” pertains to wireless ap, not the deciding condition here. Check per-VRF interface membership, per-VRF routes, route leaking configuration and tenant-specific ping vrf. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants.
“Inspect show mac address-table vlan 20, learned MAC age and ingress VLAN membership before modifying trunks” pertains to mac learning, not the deciding condition here. Check per-VRF interface membership, per-VRF routes, route leaking configuration and tenant-specific ping vrf. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants.
Question 155
Two bad design choices are hidden in this change plan: A service provider carries tenant red and tenant blue with overlapping 10.0.0.0/24 routes on one router. Which TWO should not be approved? Select TWO answers.
Explanation
Correct Answer
“Replace per-VRF route tables with merely different Layer 2 port descriptions” would violate the requirement. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants.
“Put both tenants in the same default VRF and assume overlapping prefixes remain isolated” would violate the requirement. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants.
Incorrect Answers
“Use separate VRF routing instances and bind the correct interfaces to each tenant routing table” is the controlled implementation, not an unsafe workaround. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants.
“Collect targeted evidence to check per-VRF interface membership, per-VRF routes, route leaking configuration and tenant-specific ping vrf” adds a relevant safeguard or verification step rather than weakening the solution. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants. Confirm that show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added.
“Confirm the repair by checking that show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added” adds a relevant safeguard or verification step rather than weakening the solution. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants.
Question 156
On a Cisco-based network, An enterprise needs an isolated management routing domain using the same physical routed chassis as the data network. Which change most directly solves the stated requirement?
Explanation
Correct Answer
The action 'For this LAN, use separate VRF routing instances and bind the correct interfaces to each tenant routing table.' directly addresses the vrf and routed table isolation requirement in this situation: An enterprise needs an isolated management routing domain using the same physical routed chassis as the data network. The relevant network mechanism is that vRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants. A successful change should show that show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added. To distinguish a genuine correction from a superficial change, check per-VRF interface membership, per-VRF routes, route leaking configuration and tenant-specific ping vrf.
Incorrect Answers
“Put both tenants in the same default VRF and assume overlapping prefixes remain isolated” would not meet the requirement. Instead, use separate VRF routing instances and bind the correct interfaces to each tenant routing table.
“Advertise all tenant routes to the global table without reviewing access policies” would not meet the requirement. Instead, use separate VRF routing instances and bind the correct interfaces to each tenant routing table.
“Replace per-VRF route tables with merely different Layer 2 port descriptions” does not implement the control that the facts call for. Instead, use separate VRF routing instances and bind the correct interfaces to each tenant routing table.
Question 157
A team is reviewing the design for this case: An enterprise needs an isolated management routing domain using the same physical routed chassis as the data network. What technical behavior is decisive?
Explanation
Correct Answer
VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants. Show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added.
Incorrect Answers
“Controller-managed WLANs separate centralized policy and management from the radio access point's client-facing RF service” pertains to wireless ap, not the deciding condition here. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants.
“Collapsed-core designs combine core and distribution functions, while spine-leaf fabrics use a consistent leaf-to-spine forwarding structure and equal-cost paths” would not be the most direct first check for this failure. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants.
“A Layer 2 switch learns source MAC addresses on ingress ports, forwards known unicasts toward one port, and floods unknown unicast within the associated VLAN” pertains to mac learning, not the deciding condition here. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants.
Question 158
An engineer implements a fix for 'An enterprise needs an isolated management routing domain using the same physical routed chassis as the data network.'. Which result would conclusively validate the intended change?
Explanation
Correct Answer
Show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added. If this test fails, vRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants.
Incorrect Answers
An engineer implements a fix for 'An enterprise needs an isolated management routing domain using the same physical routed chassis as the data network. The choice “the intended SSID and security policy appear consistently on joined APs, and authenticated clients roam using the same authorized WLAN” concerns wireless ap; it does not resolve the stated requirement. Show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added.
The choice “show mac address-table dynamic displays the learned source and its current interface; subsequent traffic reaches only the correct destination port” concerns mac learning; it does not resolve the stated requirement. Show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added.
An engineer implements a fix for 'An enterprise needs an isolated management routing domain using the same physical routed chassis as the data network. “Traffic follows intended redundant links with acceptable convergence, and topology diagrams show the chosen hierarchy or fabric connectivity” alone does not establish all the required behavior. Show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added.
Question 159
For the case 'An enterprise needs an isolated management routing domain using the same physical routed chassis as the data network.', which targeted checks should be compared before a disruptive change?
Explanation
Correct Answer
The investigation 'For this LAN, check per-VRF interface membership, per-VRF routes, route leaking configuration and tenant-specific ping vrf.' examines the variables most likely to explain vrf and routed table isolation in this situation: An enterprise needs an isolated management routing domain using the same physical routed chassis as the data network. Those checks are directly tied to the behavior that vRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants. The engineer can correlate this evidence with the expected outcome that show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added. and decide whether to use separate VRF routing instances and bind the correct interfaces to each tenant routing table.
Incorrect Answers
The choice “inspect AP join status, WLC WLAN profile, mapped policy profile, RF state and client association details” concerns wireless ap; it does not resolve the stated requirement. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants.
“Trace physical uplinks, check routed adjacency and ECMP entries, compare oversubscription and failure domains” would not be the most direct first check for this failure. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants.
The choice “inspect show mac address-table vlan 20, learned MAC age and ingress VLAN membership before modifying trunks” concerns mac learning; it does not resolve the stated requirement. VRF creates separate Layer 3 routing and forwarding contexts, allowing overlapping IP prefixes without automatically leaking routes between tenants.
Question 160
Network review: An enterprise needs an isolated management routing domain using the same physical routed chassis as the data network. Which TWO proposed shortcuts would be unsafe in this situation? Select TWO answers.
Explanation
Correct Answer
“Put both tenants in the same default VRF and assume overlapping prefixes remain isolated” would violate the requirement. The appropriate control instead is to use separate VRF routing instances and bind the correct interfaces to each tenant routing table.
“Replace per-VRF route tables with merely different Layer 2 port descriptions” would violate the requirement. The appropriate control instead is to use separate VRF routing instances and bind the correct interfaces to each tenant routing table.
Incorrect Answers
“use separate VRF routing instances and bind the correct interfaces to each tenant routing table” is the controlled implementation, not an unsafe workaround. Confirm that show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added.
“confirm the repair by checking that show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added.
“collect targeted evidence to check per-VRF interface membership, per-VRF routes, route leaking configuration and tenant-specific ping vrf” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that show ip route vrf RED and show ip route vrf BLUE differ; probes stay isolated unless an explicit route-leak policy is added.
Cisco Certified Network Associate (CCNA) (200-301) Practice Tests
- Cisco 200-301 Practice Test 14 - 10 Questions (Last Reviewed 04-Nov-2026)
- Cisco 200-301 Practice Test 15 - 10 Questions (Last Reviewed 03-Nov-2026)
- Cisco 200-301 Practice Test 16 - 10 Questions (Last Reviewed 02-Nov-2026)
- Cisco 200-301 Practice Test 17 - 10 Questions (Last Reviewed 01-Nov-2026)
- Cisco 200-301 Practice Test 18 - 10 Questions (Last Reviewed 31-Oct-2026)
