Pass Cisco 200-301 Exam in First Attempt Guaranteed!
Get 100% Latest Exam Questions, Accurate & Verified Answers!
30 Days Free Updates, Instant Download!
Cisco 200-301 Practice Test 12
Question 110
For this incident: A lab host is 10.18.9.112/27 and must communicate directly with 10.18.9.125. Which TWO practices introduce avoidable network risk? Select TWO answers.
Explanation
Correct Answer
“Use 10.18.9.128 as an on-link host within the /27” would violate the requirement. The appropriate control instead is to use subnet 10.18.9.96/27 with usable.97-.126 and broadcast 10.18.9.127.
A lab host is 10.18.9.112/27 and must communicate directly with 10.18.9.125. Which TWO practices introduce avoidable network risk. “Assign the.96 network identifier as the default gateway” would violate the requirement. The appropriate control instead is to use subnet 10.18.9.96/27 with usable.97-.126 and broadcast 10.18.9.127.
Incorrect Answers
“confirm the repair by checking that a gateway in .97-.126 responds to ARP; .96 remains the network address and .127 the broadcast address” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that a /27 mask is 255.255.255.224 and creates 32-address blocks; .100 and .112 are in .96-.127.
“collect targeted evidence to compare binary mask boundaries, host IP and gateway in show ip interface brief and verify same-subnet ARP” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that a /27 mask is 255.255.255.224 and creates 32-address blocks; .100 and .112 are in .96-.127.
“use subnet 10.18.9.96/27 with usable .97-.126 and broadcast 10.18.9.127” is the controlled implementation, not an unsafe workaround. Confirm that a /27 mask is 255.255.255.224 and creates 32-address blocks; .100 and .112 are in .96-.127.
Question 111
An engineer must resolve the following situation: A small office uses 192.168.33.0/24 internally but internet servers must see routable source addresses. Select the most appropriate solution.
Explanation
Correct Answer
The action 'Keep RFC1918 addressing internally and translate outbound flows through a routable external address using NAT overload.' directly addresses the private ipv4 and outbound pat requirement in this situation: A small office uses 192.168.33.0/24 internally but internet servers must see routable source addresses. The relevant network mechanism is that rFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. A successful change should show that show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds. To distinguish a genuine correction from a superficial change, inspect inside/outside interface roles, the NAT ACL, translation table, default route and external IP connectivity.
Incorrect Answers
“Disable default routing and expect NAT translation alone to reach external networks” would not meet the requirement. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. Instead, keep RFC1918 addressing internally and translate outbound flows through a routable external address using NAT overload.
“Assign the same public IP directly to every internal endpoint without NAT” does not implement the control that the facts call for. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. Instead, keep RFC1918 addressing internally and translate outbound flows through a routable external address using NAT overload.
“Advertise 10.18.6.0/24 as a globally routable Internet prefix” does not implement the control that the facts call for. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. Instead, keep RFC1918 addressing internally and translate outbound flows through a routable external address using NAT overload.
Question 112
For the condition 'A small office uses 192.168.33.0/24 internally but internet servers must see routable source addresses.' which networking principle best explains the correct solution?
Explanation
Correct Answer
RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. Keep RFC1918 addressing internally and translate outbound flows through a routable external address using NAT overload. Show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds.
Incorrect Answers
The choice “IPv6 link-local addresses are interface scoped and may repeat on different links; the interface disambiguates the neighbor” concerns ipv6 link-local next-hop; it does not resolve the stated requirement. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
“2.4-GHz Wi-Fi has limited non-overlapping 20-MHz channels; adjacent channels overlap and interfere when cells are close” does not fully explain the decisive technical boundary in this case. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. The implementation must keep RFC1918 addressing internally and translate outbound flows through a routable external address using NAT overload.
“SLAAC hosts build a global unicast address using an RA-advertised prefix; link-local FE80:: addressing exists independently of global routing” pertains to ipv6 slaac, not the deciding condition here. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. The implementation must keep RFC1918 addressing internally and translate outbound flows through a routable external address using NAT overload.
Question 113
For this situation: A small office uses 192.168.33.0/24 internally but internet servers must see routable source addresses. Which test would prove the configuration is behaving as intended?
Explanation
Correct Answer
A small office uses 192.168.33.0/24 internally but internet servers must see routable source addresses. Select the most appropriate solution. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. Show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds.
Incorrect Answers
The choice “show ipv6 route shows the correct route and interface, and neighbor discovery resolves the intended peer for off-link traffic” concerns ipv6 link-local next-hop; it does not resolve the stated requirement. Show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds.
“Spectrum survey shows reduced adjacent-channel overlap, stable signal quality and improved retransmission rates in the affected area” alone does not establish all the required behavior. Show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds.
The choice “Client shows a global /64 address and default route via the router's link-local address, and off-link IPv6 traffic succeeds” concerns ipv6 slaac; it does not resolve the stated requirement. Show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds.
Question 114
Which inspection best distinguishes the problem mechanism in this incident: A small office uses 192.168.33.0/24 internally but internet servers must see routable source addresses.
Explanation
Correct Answer
The investigation 'Inspect inside/outside interface roles, the NAT ACL, translation table, default route and external IP connectivity.' examines the variables most likely to explain private ipv4 and outbound pat in this situation: A small office uses 192.168.33.0/24 internally but internet servers must see routable source addresses. Those checks are directly tied to the behavior that rFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. The engineer can correlate this evidence with the expected outcome that show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds. and decide whether to keep RFC1918 addressing internally and translate outbound flows through a routable external address using NAT overload.
Incorrect Answers
The choice “Inspect show ipv6 neighbors, interface scope, show ipv6 route and ping ipv6 using the correct interface” concerns ipv6 link-local next-hop; it does not resolve the stated requirement. Inspect inside/outside interface roles, the NAT ACL, translation table, default route and external IP connectivity.
“Inspect AP channel assignments, channel width, neighboring RSSI, spectrum noise and radio retry statistics” would not be the most direct first check for this failure. Inspect inside/outside interface roles, the NAT ACL, translation table, default route and external IP connectivity.
The choice “Inspect show ipv6 interface, RA flags and prefixes, client ip -6 addr and ip -6 route and ICMPv6 reachability” concerns ipv6 slaac; it does not resolve the stated requirement. Inspect inside/outside interface roles, the NAT ACL, translation table, default route and external IP connectivity.
Question 115
Two bad design choices are hidden in this change plan: A small office uses 192.168.33.0/24 internally but internet servers must see routable source addresses. Which TWO should not be approved? Select TWO answers.
Explanation
Correct Answer
“Assign the same public IP directly to every internal endpoint without NAT” would violate the requirement. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
“Advertise 10.18.6.0/24 as a globally routable Internet prefix” would violate the requirement. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
Incorrect Answers
“Collect targeted evidence to inspect inside/outside interface roles, the NAT ACL, translation table, default route and external IP connectivity” adds a relevant safeguard or verification step rather than weakening the solution. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
“Confirm the repair by checking that show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds” adds a relevant safeguard or verification step rather than weakening the solution. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. Confirm that show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds.
“Keep RFC1918 addressing internally and translate outbound flows through a routable external address using NAT overload” is the controlled implementation, not an unsafe workaround. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. Confirm that show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds.
Question 116
On a Cisco-based network, An IoT network uses 10.18.6.0/24 and needs internet access without public addresses on every sensor. Which change most directly solves the stated requirement?
Explanation
Correct Answer
The action 'For this LAN, keep RFC1918 addressing internally and translate outbound flows through a routable external address using NAT overload.' directly addresses the private ipv4 and outbound pat requirement in this situation: An IoT network uses 10.18.6.0/24 and needs internet access without public addresses on every sensor. The relevant network mechanism is that rFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. A successful change should show that show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds. To distinguish a genuine correction from a superficial change, inspect inside/outside interface roles, the NAT ACL, translation table, default route and external IP connectivity.
Incorrect Answers
On a Cisco-based network, An IoT network uses 10.18.6.0/24 and needs internet access without public addresses on every sensor. “advertise 10.18.6.0/24 as a globally routable Internet prefix” does not implement the control that the facts call for. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. Instead, keep RFC1918 addressing internally and translate outbound flows through a routable external address using NAT overload.
On a Cisco-based network, An IoT network uses 10.18.6.0/24 and needs internet access without public addresses on every sensor. “Disable default routing and expect NAT translation alone to reach external networks” would not meet the requirement. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. Instead, keep RFC1918 addressing internally and translate outbound flows through a routable external address using NAT overload.
On a Cisco-based network, An IoT network uses 10.18.6.0/24 and needs internet access without public addresses on every sensor. “assign the same public IP directly to every internal endpoint without NAT” does not implement the control that the facts call for. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. Instead, keep RFC1918 addressing internally and translate outbound flows through a routable external address using NAT overload.
Question 117
A team is reviewing the design for this case: An IoT network uses 10.18.6.0/24 and needs internet access without public addresses on every sensor. What technical behavior is decisive?
Explanation
Correct Answer
RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. Keep RFC1918 addressing internally and translate outbound flows through a routable external address using NAT overload.
Incorrect Answers
“2.4-GHz Wi-Fi has limited non-overlapping 20-MHz channels; adjacent channels overlap and interfere when cells are close” does not fully explain the decisive technical boundary in this case. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
An IoT network uses 10.18.6.0/24 and needs internet access without public addresses on every sensor. The choice “iPv6 link-local addresses are interface scoped and may repeat on different links; the interface disambiguates the neighbor” concerns ipv6 link-local next-hop; it does not resolve the stated requirement. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
The choice “sLAAC hosts build a global unicast address using an RA-advertised prefix; link-local FE80:: addressing exists independently of global routing” concerns ipv6 slaac; it does not resolve the stated requirement. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
Question 118
An engineer implements a fix for 'An IoT network uses 10.18.6.0/24 and needs internet access without public addresses on every sensor.'. Which result would conclusively validate the intended change?
Explanation
Correct Answer
On a Cisco-based network, An IoT network uses 10.18.6.0/24 and needs internet access without public addresses on every sensor. Which change most directly solves the stated requirement. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. Show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds.
Incorrect Answers
“Show ipv6 route shows the correct route and interface, and neighbor discovery resolves the intended peer for off-link traffic” pertains to ipv6 link-local next-hop, not the deciding condition here. Show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
“Spectrum survey shows reduced adjacent-channel overlap, stable signal quality and improved retransmission rates in the affected area” alone does not establish all the required behavior. Show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
“Client shows a global /64 address and default route via the router's link-local address, and off-link IPv6 traffic succeeds” pertains to ipv6 slaac, not the deciding condition here. Show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
Question 119
For the case 'An IoT network uses 10.18.6.0/24 and needs internet access without public addresses on every sensor.', which targeted checks should be compared before a disruptive change?
Explanation
Correct Answer
The investigation 'For this LAN, inspect inside/outside interface roles, the NAT ACL, translation table, default route and external IP connectivity.' examines the variables most likely to explain private ipv4 and outbound pat in this situation: An IoT network uses 10.18.6.0/24 and needs internet access without public addresses on every sensor. Those checks are directly tied to the behavior that rFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address. The engineer can correlate this evidence with the expected outcome that show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds. and decide whether to keep RFC1918 addressing internally and translate outbound flows through a routable external address using NAT overload.
Incorrect Answers
“Inspect show ipv6 interface, RA flags and prefixes, client ip -6 addr and ip -6 route and ICMPv6 reachability” pertains to ipv6 slaac, not the deciding condition here. Inspect inside/outside interface roles, the NAT ACL, translation table, default route and external IP connectivity. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
“Inspect show ipv6 neighbors, interface scope, show ipv6 route and ping ipv6 using the correct interface” pertains to ipv6 link-local next-hop, not the deciding condition here. Inspect inside/outside interface roles, the NAT ACL, translation table, default route and external IP connectivity. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
“Inspect AP channel assignments, channel width, neighboring RSSI, spectrum noise and radio retry statistics” would not be the most direct first check for this failure. Inspect inside/outside interface roles, the NAT ACL, translation table, default route and external IP connectivity. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
Question 120
Network review: An IoT network uses 10.18.6.0/24 and needs internet access without public addresses on every sensor. Which TWO proposed shortcuts would be unsafe in this situation? Select TWO answers.
Explanation
Correct Answer
An IoT network uses 10.18.6.0/24 and needs internet access without public addresses on every sensor. “Assign the same public IP directly to every internal endpoint without NAT” would violate the requirement. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
An IoT network uses 10.18.6.0/24 and needs internet access without public addresses on every sensor. “Advertise 10.18.6.0/24 as a globally routable Internet prefix” would violate the requirement. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
Incorrect Answers
“keep RFC1918 addressing internally and translate outbound flows through a routable external address using NAT overload” is the controlled implementation, not an unsafe workaround. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
An IoT network uses 10.18.6.0/24 and needs internet access without public addresses on every sensor. “collect targeted evidence to inspect inside/outside interface roles, the NAT ACL, translation table, default route and external IP connectivity” adds a relevant safeguard or verification step rather than weakening the solution. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
“confirm the repair by checking that show ip nat translations displays distinct inside-local source sockets sharing the intended inside-global address while external connectivity succeeds” adds a relevant safeguard or verification step rather than weakening the solution. RFC1918 private IPv4 prefixes are not publicly routed on the Internet; PAT can map many private source ports to one global address.
Cisco Certified Network Associate (CCNA) (200-301) Practice Tests
- Cisco 200-301 Practice Test 10 - 10 Questions (Last Reviewed 08-Nov-2026)
- Cisco 200-301 Practice Test 11 - 10 Questions (Last Reviewed 07-Nov-2026)
- Cisco 200-301 Practice Test 12 - 10 Questions (Last Reviewed 06-Nov-2026)
- Cisco 200-301 Practice Test 13 - 10 Questions (Last Reviewed 05-Nov-2026)
- Cisco 200-301 Practice Test 14 - 10 Questions (Last Reviewed 04-Nov-2026)
