Cisco 200-301 Practice Test 7 - Prepaway
Practice Exams:

Pass Cisco 200-301 Exam in First Attempt Guaranteed!

Get 100% Latest Exam Questions, Accurate & Verified Answers!

30 Days Free Updates, Instant Download!

Verified By Experts
Premium Bundle
$29.98
$79.99 $109.97

200-301 Premium Bundle


  • Premium File 760 Questions & Answers. Last update: Nov 10, 2026
  • Training Course 271 Lectures
  • Study Guide 1969 Pages

Cisco 200-301 Practice Test 7

Question 60

Network review: A camera runs through a patch panel and drops its Ethernet link intermittently when the cable is disturbed. Which TWO proposed shortcuts would be unsafe in this situation? Select TWO answers.

  1. For this LAN, enable a routing protocol on the failing physical interface to restore broken wire pairs.
  2. For this LAN, collect targeted evidence to check cable test results, show interface speed/duplex, run TDR when supported and examine CRC and alignment counters.
  3. For this LAN, test and replace the damaged copper segment and validate pair continuity and interface autonegotiation.
  4. For this LAN, confirm the repair by checking that cable certification passes and both interfaces maintain the intended duplex and speed with counters stable under traffic.
  5. For this LAN, force 10 Mbps half duplex without testing the cable fault.

Explanation

Correct Answer

A:

A camera runs through a patch panel and drops its Ethernet link intermittently when the cable is disturbed. “Enable a routing protocol on the failing physical interface to restore broken wire pairs” would violate the requirement. Twisted-pair Ethernet needs appropriate wire pairs and cable quality; damaged or missing pairs can reduce speed or cause loss.

E:

A camera runs through a patch panel and drops its Ethernet link intermittently when the cable is disturbed. “Force 10 Mbps half duplex without testing the cable fault” would violate the requirement. Twisted-pair Ethernet needs appropriate wire pairs and cable quality; damaged or missing pairs can reduce speed or cause loss.

Incorrect Answers

B:

A camera runs through a patch panel and drops its Ethernet link intermittently when the cable is disturbed. “collect targeted evidence to check cable test results, show interface speed/duplex, run TDR when supported and examine CRC and alignment counters” adds a relevant safeguard or verification step rather than weakening the solution. Twisted-pair Ethernet needs appropriate wire pairs and cable quality; damaged or missing pairs can reduce speed or cause loss.

C:

“test and replace the damaged copper segment and validate pair continuity and interface autonegotiation” is the controlled implementation, not an unsafe workaround. Twisted-pair Ethernet needs appropriate wire pairs and cable quality; damaged or missing pairs can reduce speed or cause loss.

D:

A camera runs through a patch panel and drops its Ethernet link intermittently when the cable is disturbed. “confirm the repair by checking that cable certification passes and both interfaces maintain the intended duplex and speed with counters stable under traffic” adds a relevant safeguard or verification step rather than weakening the solution. Twisted-pair Ethernet needs appropriate wire pairs and cable quality; damaged or missing pairs can reduce speed or cause loss.

Question 61

Consider this operational failure: A branch switch port runs full duplex while the attached unmanaged endpoint works half duplex, with collisions and poor throughput. What should the administrator implement first?

  1. Ignore growing FCS errors because the switch port shows connected.
  2. Force full duplex on only one side while leaving the other mismatched.
  3. Correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported.
  4. Increase the OSPF hello timer to suppress physical-layer collisions.

Explanation

Correct Answer

C:

The action 'Correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported.' directly addresses the duplex mismatch on ethernet requirement in this situation: A branch switch port runs full duplex while the attached unmanaged endpoint works half duplex, with collisions and poor throughput. The relevant network mechanism is that duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up. A successful change should show that show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex. To distinguish a genuine correction from a superficial change, inspect both ends' speed/duplex settings and show interfaces collision, late-collision, FCS and runts counters.

Incorrect Answers

A:

“Ignore growing FCS errors because the switch port shows connected” would not meet the requirement. Instead, correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported.

B:

“Force full duplex on only one side while leaving the other mismatched” does not implement the control that the facts call for. Instead, correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported.

D:

“Increase the OSPF hello timer to suppress physical-layer collisions” does not implement the control that the facts call for. Instead, correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported.

Question 62

While troubleshooting 'A branch switch port runs full duplex while the attached unmanaged endpoint works half duplex, with collisions and poor throughput.', which underlying protocol rule should guide the decision?

  1. A Layer 2 switch learns source MAC addresses on ingress ports, forwards known unicasts toward one port, and floods unknown unicast within the associated VLAN.
  2. Controller-managed WLANs separate centralized policy and management from the radio access point's client-facing RF service.
  3. Collapsed-core designs combine core and distribution functions, while spine-leaf fabrics use a consistent leaf-to-spine forwarding structure and equal-cost paths.
  4. Duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.

Explanation

Correct Answer

D:

Duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up. Show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex.

Incorrect Answers

A:

The choice “A Layer 2 switch learns source MAC addresses on ingress ports, forwards known unicasts toward one port, and floods unknown unicast within the associated VLAN” concerns mac learning; it does not resolve the stated requirement. Duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.

B:

The choice “Controller-managed WLANs separate centralized policy and management from the radio access point's client-facing RF service” concerns wireless ap; it does not resolve the stated requirement. Duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.

C:

“Collapsed-core designs combine core and distribution functions, while spine-leaf fabrics use a consistent leaf-to-spine forwarding structure and equal-cost paths” would not be the most direct first check for this failure. Duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.

Question 63

Which measurable result should be checked before closing this ticket: A branch switch port runs full duplex while the attached unmanaged endpoint works half duplex, with collisions and poor throughput.

  1. The intended SSID and security policy appear consistently on joined APs, and authenticated clients roam using the same authorized WLAN.
  2. show mac address-table dynamic displays the learned source and its current interface; subsequent traffic reaches only the correct destination port.
  3. show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex.
  4. Traffic follows intended redundant links with acceptable convergence, and topology diagrams show the chosen hierarchy or fabric connectivity.

Explanation

Correct Answer

C:

Show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex. Correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported.

Incorrect Answers

A:

“The intended SSID and security policy appear consistently on joined APs, and authenticated clients roam using the same authorized WLAN” pertains to wireless ap, not the deciding condition here. Show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex.

B:

“Show mac address-table dynamic displays the learned source and its current interface; subsequent traffic reaches only the correct destination port” pertains to mac learning, not the deciding condition here. Show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex.

D:

“Traffic follows intended redundant links with acceptable convergence, and topology diagrams show the chosen hierarchy or fabric connectivity” alone does not establish all the required behavior. Show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex.

Question 64

Before modifying more devices to address 'A branch switch port runs full duplex while the attached unmanaged endpoint works half duplex, with collisions and poor throughput.', which diagnostic evidence is most relevant?

  1. Inspect show mac address-table vlan 20, learned MAC age and ingress VLAN membership before modifying trunks.
  2. Inspect AP join status, WLC WLAN profile, mapped policy profile, RF state and client association details.
  3. Trace physical uplinks, check routed adjacency and ECMP entries, compare oversubscription and failure domains.
  4. Inspect both ends' speed/duplex settings and show interfaces collision, late-collision, FCS and runts counters.

Explanation

Correct Answer

D:

The investigation 'Inspect both ends' speed/duplex settings and show interfaces collision, late-collision, FCS and runts counters.' examines the variables most likely to explain duplex mismatch on ethernet in this situation: A branch switch port runs full duplex while the attached unmanaged endpoint works half duplex, with collisions and poor throughput. Those checks are directly tied to the behavior that duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up. The engineer can correlate this evidence with the expected outcome that show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex. and decide whether to correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported.

Incorrect Answers

A:

“Inspect show mac address-table vlan 20, learned MAC age and ingress VLAN membership before modifying trunks” pertains to mac learning, not the deciding condition here. Duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.

B:

“Inspect AP join status, WLC WLAN profile, mapped policy profile, RF state and client association details” pertains to wireless ap, not the deciding condition here. Duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.

C:

“Trace physical uplinks, check routed adjacency and ECMP entries, compare oversubscription and failure domains” would not be the most direct first check for this failure. Duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.

Question 65

A change board considers the issue 'A branch switch port runs full duplex while the attached unmanaged endpoint works half duplex, with collisions and poor throughput.'. Identify the TWO decisions that should be rejected. Select TWO answers.

  1. Increase the OSPF hello timer to suppress physical-layer collisions.
  2. Confirm the repair by checking that show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex.
  3. Correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported.
  4. Force full duplex on only one side while leaving the other mismatched.
  5. Collect targeted evidence to inspect both ends' speed/duplex settings and show interfaces collision, late-collision, FCS and runts counters.

Explanation

Correct Answer

A:

“Increase the OSPF hello timer to suppress physical-layer collisions” would violate the requirement.

D:

“Force full duplex on only one side while leaving the other mismatched” would violate the requirement.

Incorrect Answers

B:

“Confirm the repair by checking that show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex.

C:

“Correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported” is the controlled implementation, not an unsafe workaround. An important verification is that show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex.

E:

“Collect targeted evidence to inspect both ends' speed/duplex settings and show interfaces collision, late-collision, FCS and runts counters” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex.

Question 66

A network operator receives this ticket: A factory printer experiences late collisions after one side of a copper link is manually forced to an incompatible duplex setting. Which configuration is best suited to the reported issue?

  1. For this LAN, correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported.
  2. For this LAN, increase the OSPF hello timer to suppress physical-layer collisions.
  3. For this LAN, ignore growing FCS errors because the switch port shows connected.
  4. For this LAN, force full duplex on only one side while leaving the other mismatched.

Explanation

Correct Answer

A:

The action 'For this LAN, correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported.' directly addresses the duplex mismatch on ethernet requirement in this situation: A factory printer experiences late collisions after one side of a copper link is manually forced to an incompatible duplex setting. The relevant network mechanism is that duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up. A successful change should show that show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex. To distinguish a genuine correction from a superficial change, inspect both ends' speed/duplex settings and show interfaces collision, late-collision, FCS and runts counters.

Incorrect Answers

B:

A factory printer experiences late collisions after one side of a copper link is manually forced to an incompatible duplex setting. “Increase the OSPF hello timer to suppress physical-layer collisions” does not implement the control that the facts call for. Instead, correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported.

C:

A factory printer experiences late collisions after one side of a copper link is manually forced to an incompatible duplex setting. “Ignore growing FCS errors because the switch port shows connected” would not meet the requirement. Instead, correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported.

D:

A factory printer experiences late collisions after one side of a copper link is manually forced to an incompatible duplex setting. “Force full duplex on only one side while leaving the other mismatched” does not implement the control that the facts call for. Instead, correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported.

Question 67

Which network-layer or protocol behavior most directly explains the result in this case: A factory printer experiences late collisions after one side of a copper link is manually forced to an incompatible duplex setting.

  1. For this LAN, a Layer 2 switch learns source MAC addresses on ingress ports, forwards known unicasts toward one port, and floods unknown unicast within the associated VLAN.
  2. For this LAN, duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.
  3. For this LAN, controller-managed WLANs separate centralized policy and management from the radio access point's client-facing RF service.
  4. For this LAN, collapsed-core designs combine core and distribution functions, while spine-leaf fabrics use a consistent leaf-to-spine forwarding structure and equal-cost paths.

Explanation

Correct Answer

B:

Because a network operator receives this ticket: A factory printer experiences late collisions after one side of a copper link is manually forced to an incompatible duplex setting, duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.

Incorrect Answers

A:

“A Layer 2 switch learns source MAC addresses on ingress ports, forwards known unicasts toward one port, and floods unknown unicast within the associated VLAN” pertains to mac learning, not the deciding condition here. Duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.

C:

“Controller-managed WLANs separate centralized policy and management from the radio access point's client-facing RF service” pertains to wireless ap, not the deciding condition here. Duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.

D:

“Collapsed-core designs combine core and distribution functions, while spine-leaf fabrics use a consistent leaf-to-spine forwarding structure and equal-cost paths” alone does not establish all the required behavior. Duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.

Question 68

After correcting 'A factory printer experiences late collisions after one side of a copper link is manually forced to an incompatible duplex setting.', which observation is the strongest evidence that the specific requirement is met?

  1. For this LAN, traffic follows intended redundant links with acceptable convergence, and topology diagrams show the chosen hierarchy or fabric connectivity.
  2. For this LAN, show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex.
  3. For this LAN, show mac address-table dynamic displays the learned source and its current interface; subsequent traffic reaches only the correct destination port.
  4. For this LAN, the intended SSID and security policy appear consistently on joined APs, and authenticated clients roam using the same authorized WLAN.

Explanation

Correct Answer

B:

A network operator receives this ticket: A factory printer experiences late collisions after one side of a copper link is manually forced to an incompatible duplex setting. Duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.

Incorrect Answers

A:

“Traffic follows intended redundant links with acceptable convergence, and topology diagrams show the chosen hierarchy or fabric connectivity” alone does not establish all the required behavior. Duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.

C:

“Show mac address-table dynamic displays the learned source and its current interface; subsequent traffic reaches only the correct destination port” pertains to mac learning, not the deciding condition here. Duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.

D:

“The intended SSID and security policy appear consistently on joined APs, and authenticated clients roam using the same authorized WLAN” pertains to wireless ap, not the deciding condition here. Duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.

Question 69

An operator is triaging the issue 'A factory printer experiences late collisions after one side of a copper link is manually forced to an incompatible duplex setting.'. What should be inspected to isolate the actual cause?

  1. For this LAN, trace physical uplinks, check routed adjacency and ECMP entries, compare oversubscription and failure domains.
  2. For this LAN, inspect both ends' speed/duplex settings and show interfaces collision, late-collision, FCS and runts counters.
  3. For this LAN, inspect AP join status, WLC WLAN profile, mapped policy profile, RF state and client association details.
  4. For this LAN, inspect show mac address-table vlan 20, learned MAC age and ingress VLAN membership before modifying trunks.

Explanation

Correct Answer

B:

The investigation 'For this LAN, inspect both ends' speed/duplex settings and show interfaces collision, late-collision, FCS and runts counters.' examines the variables most likely to explain duplex mismatch on ethernet in this situation: A factory printer experiences late collisions after one side of a copper link is manually forced to an incompatible duplex setting. Those checks are directly tied to the behavior that duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up. The engineer can correlate this evidence with the expected outcome that show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex. and decide whether to correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported.

Incorrect Answers

A:

“Trace physical uplinks, check routed adjacency and ECMP entries, compare oversubscription and failure domains” would not be the most direct first check for this failure. Inspect both ends' speed/duplex settings and show interfaces collision, late-collision, FCS and runts counters.

C:

The choice “inspect AP join status, WLC WLAN profile, mapped policy profile, RF state and client association details” concerns wireless ap; it does not resolve the stated requirement. Inspect both ends' speed/duplex settings and show interfaces collision, late-collision, FCS and runts counters.

D:

The choice “inspect show mac address-table vlan 20, learned MAC age and ingress VLAN membership before modifying trunks” concerns mac learning; it does not resolve the stated requirement. Inspect both ends' speed/duplex settings and show interfaces collision, late-collision, FCS and runts counters.

Question 70

For this incident: A factory printer experiences late collisions after one side of a copper link is manually forced to an incompatible duplex setting. Which TWO practices introduce avoidable network risk? Select TWO answers.

  1. For this LAN, collect targeted evidence to inspect both ends' speed/duplex settings and show interfaces collision, late-collision, FCS and runts counters.
  2. For this LAN, confirm the repair by checking that show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex.
  3. For this LAN, correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported.
  4. For this LAN, increase the OSPF hello timer to suppress physical-layer collisions.
  5. For this LAN, force full duplex on only one side while leaving the other mismatched.

Explanation

Correct Answer

D:

A factory printer experiences late collisions after one side of a copper link is manually forced to an incompatible duplex setting. “Increase the OSPF hello timer to suppress physical-layer collisions” would violate the requirement.

E:

A factory printer experiences late collisions after one side of a copper link is manually forced to an incompatible duplex setting. “Force full duplex on only one side while leaving the other mismatched” would violate the requirement.

Incorrect Answers

A:

“collect targeted evidence to inspect both ends' speed/duplex settings and show interfaces collision, late-collision, FCS and runts counters” adds a relevant safeguard or verification step rather than weakening the solution.

B:

“confirm the repair by checking that show interfaces counters stop increasing and file transfers sustain expected throughput after both ports agree on duplex” adds a relevant safeguard or verification step rather than weakening the solution.

C:

“correct duplex and speed configuration on both ends, preferably compatible auto-negotiation where supported” is the controlled implementation, not an unsafe workaround. An important verification is that duplex mismatch creates collisions or late collisions on one end and FCS or runts on the other even while link LEDs remain up.

Cisco Certified Network Associate (CCNA) (200-301) Practice Tests