Pass Cisco 200-301 Exam in First Attempt Guaranteed!
Get 100% Latest Exam Questions, Accurate & Verified Answers!
30 Days Free Updates, Instant Download!
Cisco 200-301 Practice Test 43
Question 420
Network review: A campus router needs to advertise its connected LAN prefixes into single-area OSPF area 0. Which TWO proposed shortcuts would be unsafe in this situation? Select TWO answers.
Explanation
Correct Answer
A campus router needs to advertise its connected LAN prefixes into single-area OSPF area 0. Which TWO proposed shortcuts would be unsafe in this situation. “Put the transit peers in different OSPF areas without a correct ABR design” would violate the requirement. An OSPF network statement matches local interface addresses using a wildcard mask and enables OSPF participation in that area.
A campus router needs to advertise its connected LAN prefixes into single-area OSPF area 0. Which TWO proposed shortcuts would be unsafe in this situation. “Configure a network statement that matches no local transit interface” would violate the requirement. An OSPF network statement matches local interface addresses using a wildcard mask and enables OSPF participation in that area.
Incorrect Answers
A campus router needs to advertise its connected LAN prefixes into single-area OSPF area 0. Which TWO proposed shortcuts would be unsafe in this situation. “collect targeted evidence to inspect show ip protocols, network wildcard matching, show ip ospf interface and router process configuration” adds a relevant safeguard or verification step rather than weakening the solution. An OSPF network statement matches local interface addresses using a wildcard mask and enables OSPF participation in that area.
“enable OSPF on the intended transit interfaces in the correct area and advertise the required connected prefixes” is the controlled implementation, not an unsafe workaround. An OSPF network statement matches local interface addresses using a wildcard mask and enables OSPF participation in that area.
“confirm the repair by checking that show ip ospf neighbor reaches FULL and show ip route ospf contains the intended remote prefixes” adds a relevant safeguard or verification step rather than weakening the solution. An OSPF network statement matches local interface addresses using a wildcard mask and enables OSPF participation in that area.
Question 421
Consider this operational failure: Two routers share a /30 Ethernet transit segment, but one interface belongs to area 0 and its peer is in area 10. What should the administrator implement first?
Explanation
Correct Answer
The action 'Configure a common OSPF area on the same adjacency segment while maintaining a valid backbone topology.' directly addresses the ospf area mismatch adjacency requirement in this situation: Two routers share a /30 Ethernet transit segment, but one interface belongs to area 0 and its peer is in area 10. The relevant network mechanism is that oSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation. A successful change should show that show ip ospf neighbor reports FULL and show ip ospf interface on both sides shows the same area. To distinguish a genuine correction from a superficial change, inspect show ip ospf interface, hello area identifiers and relevant process network statements.
Incorrect Answers
“Add a static default route and assume it establishes OSPF neighborhood” would not meet the requirement. Instead, configure a common OSPF area on the same adjacency segment while maintaining a valid backbone topology.
“Only change the OSPF router ID while keeping the area mismatch” does not implement the control that the facts call for. Instead, configure a common OSPF area on the same adjacency segment while maintaining a valid backbone topology.
“Increase an interface bandwidth value to bypass incompatible OSPF area IDs” would not meet the requirement. Instead, configure a common OSPF area on the same adjacency segment while maintaining a valid backbone topology.
Question 422
While troubleshooting 'Two routers share a /30 Ethernet transit segment, but one interface belongs to area 0 and its peer is in area 10.', which underlying protocol rule should guide the decision?
Explanation
Correct Answer
OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation. Show ip ospf neighbor reports FULL and show ip ospf interface on both sides shows the same area.
Incorrect Answers
“Routing metric ranks candidate paths learned through the same protocol; OSPF path cost is based on configured interface costs, not simply hop count” pertains to routing metrics within one protocol, not the deciding condition here. OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
The choice “A static route maps an IP destination prefix to a next hop or exit interface; the next hop must itself be resolved through a connected route” concerns ipv4 next-hop static route; it does not resolve the stated requirement. OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
“A host ARPs for its on-link default gateway to send off-subnet packets; a gateway outside the local prefix cannot normally be resolved directly” pertains to ipv4 host default gateway, not the deciding condition here. OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
Question 423
Which measurable result should be checked before closing this ticket: Two routers share a /30 Ethernet transit segment, but one interface belongs to area 0 and its peer is in area 10.
Explanation
Correct Answer
Show ip ospf neighbor reports FULL and show ip ospf interface on both sides shows the same area. If this test fails, oSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
Incorrect Answers
The choice “show ip route lists the static destination and packet forwarding reaches the remote subnet through the intended WAN neighbor” concerns ipv4 next-hop static route; it does not resolve the stated requirement. Show ip ospf neighbor reports FULL and show ip ospf interface on both sides shows the same area.
“The host resolves its gateway MAC, reaches a remote network, and traceroute shows a first-hop device on the local VLAN” pertains to ipv4 host default gateway, not the deciding condition here. Show ip ospf neighbor reports FULL and show ip ospf interface on both sides shows the same area.
The choice “show ip route and show ip ospf interface show the expected preferred path or eligible equal-cost next hops” concerns routing metrics within one protocol; it does not resolve the stated requirement. Show ip ospf neighbor reports FULL and show ip ospf interface on both sides shows the same area.
Question 424
Before modifying more devices to address 'Two routers share a /30 Ethernet transit segment, but one interface belongs to area 0 and its peer is in area 10.', which diagnostic evidence is most relevant?
Explanation
Correct Answer
The investigation 'Inspect show ip ospf interface, hello area identifiers and relevant process network statements.' examines the variables most likely to explain ospf area mismatch adjacency in this situation: Two routers share a /30 Ethernet transit segment, but one interface belongs to area 0 and its peer is in area 10. Those checks are directly tied to the behavior that oSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation. The engineer can correlate this evidence with the expected outcome that show ip ospf neighbor reports FULL and show ip ospf interface on both sides shows the same area. and decide whether to configure a common OSPF area on the same adjacency segment while maintaining a valid backbone topology.
Incorrect Answers
The choice “Inspect OSPF path costs, interface bandwidth/reference settings and the actual destination's routing entry” concerns routing metrics within one protocol; it does not resolve the stated requirement. OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
The choice “Inspect ip route configuration, show ip route, ARP for directly connected next hop and traceroute from branch hosts” concerns ipv4 next-hop static route; it does not resolve the stated requirement. OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
“Inspect ipconfig, network mask, arp -a, ping gateway, VLAN membership and the router's interface IP” pertains to ipv4 host default gateway, not the deciding condition here. OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
Question 425
A change board considers the issue 'Two routers share a /30 Ethernet transit segment, but one interface belongs to area 0 and its peer is in area 10.'. Identify the TWO decisions that should be rejected. Select TWO answers.
Explanation
Correct Answer
“Increase an interface bandwidth value to bypass incompatible OSPF area IDs” would violate the requirement. The appropriate control instead is to configure a common OSPF area on the same adjacency segment while maintaining a valid backbone topology.
“Only change the OSPF router ID while keeping the area mismatch” would violate the requirement. The appropriate control instead is to configure a common OSPF area on the same adjacency segment while maintaining a valid backbone topology.
Incorrect Answers
“Collect targeted evidence to inspect show ip ospf interface, hello area identifiers and relevant process network statements” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that show ip ospf neighbor reports FULL and show ip ospf interface on both sides shows the same area.
“Configure a common OSPF area on the same adjacency segment while maintaining a valid backbone topology” is the controlled implementation, not an unsafe workaround.
“Confirm the repair by checking that show ip ospf neighbor reports FULL and show ip ospf interface on both sides shows the same area” adds a relevant safeguard or verification step rather than weakening the solution.
Question 426
A network operator receives this ticket: A branch's OSPF interface was moved to area 1 while the upstream peer remains in backbone area 0. Which configuration is best suited to the reported issue?
Explanation
Correct Answer
Configure a common OSPF area on the same adjacency segment while maintaining a valid backbone topology. OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
Incorrect Answers
A branch's OSPF interface was moved to area 1 while the upstream peer remains in backbone area 0. “Increase an interface bandwidth value to bypass incompatible OSPF area IDs” would not meet the requirement. Instead, configure a common OSPF area on the same adjacency segment while maintaining a valid backbone topology.
A branch's OSPF interface was moved to area 1 while the upstream peer remains in backbone area 0. “Add a static default route and assume it establishes OSPF neighborhood” would not meet the requirement. Instead, configure a common OSPF area on the same adjacency segment while maintaining a valid backbone topology.
A branch's OSPF interface was moved to area 1 while the upstream peer remains in backbone area 0. “Only change the OSPF router ID while keeping the area mismatch” does not implement the control that the facts call for. Instead, configure a common OSPF area on the same adjacency segment while maintaining a valid backbone topology.
Question 427
Which network-layer or protocol behavior most directly explains the result in this case: A branch's OSPF interface was moved to area 1 while the upstream peer remains in backbone area 0.
Explanation
Correct Answer
OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation. If this test fails, inspect show ip ospf interface, hello area identifiers and relevant process network statements.
Incorrect Answers
The choice “routing metric ranks candidate paths learned through the same protocol; OSPF path cost is based on configured interface costs, not simply hop count” concerns routing metrics within one protocol; it does not resolve the stated requirement. OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
A branch's OSPF interface was moved to area 1 while the upstream peer remains in backbone area 0. The choice “a static route maps an IP destination prefix to a next hop or exit interface; the next hop must itself be resolved through a connected route” concerns ipv4 next-hop static route; it does not resolve the stated requirement. OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
The choice “a host ARPs for its on-link default gateway to send off-subnet packets; a gateway outside the local prefix cannot normally be resolved directly” concerns ipv4 host default gateway; it does not resolve the stated requirement. OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
Question 428
After correcting 'A branch's OSPF interface was moved to area 1 while the upstream peer remains in backbone area 0.', which observation is the strongest evidence that the specific requirement is met?
Explanation
Correct Answer
OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation. Configure a common OSPF area on the same adjacency segment while maintaining a valid backbone topology.
Incorrect Answers
The choice “the host resolves its gateway MAC, reaches a remote network, and traceroute shows a first-hop device on the local VLAN” concerns ipv4 host default gateway; it does not resolve the stated requirement. OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
The choice “show ip route and show ip ospf interface show the expected preferred path or eligible equal-cost next hops” concerns routing metrics within one protocol; it does not resolve the stated requirement. OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
The choice “show ip route lists the static destination and packet forwarding reaches the remote subnet through the intended WAN neighbor” concerns ipv4 next-hop static route; it does not resolve the stated requirement. OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
Question 429
An operator is triaging the issue 'A branch's OSPF interface was moved to area 1 while the upstream peer remains in backbone area 0.'. What should be inspected to isolate the actual cause?
Explanation
Correct Answer
Inspect show ip ospf interface, hello area identifiers and relevant process network statements. OSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
Incorrect Answers
“Inspect ipconfig, network mask, arp -a, ping gateway, VLAN membership and the router's interface IP” pertains to ipv4 host default gateway, not the deciding condition here. Inspect show ip ospf interface, hello area identifiers and relevant process network statements.
“Inspect ip route configuration, show ip route, ARP for directly connected next hop and traceroute from branch hosts” pertains to ipv4 next-hop static route, not the deciding condition here. Inspect show ip ospf interface, hello area identifiers and relevant process network statements.
“Inspect OSPF path costs, interface bandwidth/reference settings and the actual destination's routing entry” pertains to routing metrics within one protocol, not the deciding condition here. Inspect show ip ospf interface, hello area identifiers and relevant process network statements.
Question 430
For this incident: A branch's OSPF interface was moved to area 1 while the upstream peer remains in backbone area 0. Which TWO practices introduce avoidable network risk? Select TWO answers.
Explanation
Correct Answer
A branch's OSPF interface was moved to area 1 while the upstream peer remains in backbone area 0. Which TWO practices introduce avoidable network risk. “Only change the OSPF router ID while keeping the area mismatch” would violate the requirement. The appropriate control instead is to configure a common OSPF area on the same adjacency segment while maintaining a valid backbone topology.
A branch's OSPF interface was moved to area 1 while the upstream peer remains in backbone area 0. Which TWO practices introduce avoidable network risk. “Increase an interface bandwidth value to bypass incompatible OSPF area IDs” would violate the requirement. The appropriate control instead is to configure a common OSPF area on the same adjacency segment while maintaining a valid backbone topology.
Incorrect Answers
“configure a common OSPF area on the same adjacency segment while maintaining a valid backbone topology” is the controlled implementation, not an unsafe workaround. Confirm that oSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
“collect targeted evidence to inspect show ip ospf interface, hello area identifiers and relevant process network statements” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that oSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
“confirm the repair by checking that show ip ospf neighbor reports FULL and show ip ospf interface on both sides shows the same area” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that oSPF hello packets must match key adjacency parameters including the area ID; unequal area IDs block neighbor formation.
Cisco Certified Network Associate (CCNA) (200-301) Practice Tests
- Cisco 200-301 Practice Test 41 - 10 Questions (Last Reviewed 08-Oct-2026)
- Cisco 200-301 Practice Test 42 - 10 Questions (Last Reviewed 07-Oct-2026)
- Cisco 200-301 Practice Test 43 - 10 Questions (Last Reviewed 06-Oct-2026)
- Cisco 200-301 Practice Test 44 - 10 Questions (Last Reviewed 05-Oct-2026)
- Cisco 200-301 Practice Test 45 - 10 Questions (Last Reviewed 04-Oct-2026)
