Pass Juniper JN0-364 Exam in First Attempt Guaranteed!
Get 100% Latest Exam Questions, Accurate & Verified Answers!
30 Days Free Updates, Instant Download!
Juniper JN0-364 Practice Test 7
Question 60
A fictional Junos service-provider engineer encounters this scenario: A metro access aggregation router stays stuck without an OSPF adjacency to its backbone uplink after a site template is copied from a nonbackbone area. Distinguishing evidence: Interface-level OSPF inspection shows the local circuit attached to area 0.0.0.1 while the peer expects area 0.0.0.0 on the same numbered link. Which bounded approval scope avoids unintended changes to other provider or customer services?
Answer and Explanation
Correct Answer: D
A separate release decision would approve only the bounded change (Inspect IS-IS LSP flooding, level scope and database synchronization before deciding on targeted refresh or isolation steps.) after independently checking (Peer databases converge on the expected LSP set and the authorized loopback routes become usable without forcing widespread protocol resets.), without quietly widening the provider or customer network scope. It does not match the current change: Validate the inter-router interface, area design and active configuration, then align the intended area membership under the appropriate OSPF instance.
An alternative approval would approve only the bounded change (Review the OSPF export policy and prefix scope, then explicitly permit only the approved external destination while preserving other route exclusions.) after independently checking (Neighbor route views receive the approved external prefix and unrelated tenant networks remain unadvertised.), without quietly widening the provider or customer network scope. The relevant evidence and acceptance are Interface-level OSPF inspection shows the local circuit attached to area 0.0.0.1 while the peer expects area 0.0.0.0 on the same numbered link and Both routers progress to the expected full adjacency and the correct link-state routes appear without shifting unrelated interfaces into area zero, respectively.
Another proposed approval would approve only the bounded change (Check approved liveness requirements and align the interface hello and dead parameters on both adjacent devices before committing.) after independently checking (The neighbor remains full through several monitored intervals, while routing reconverges predictably on a controlled link loss.), without quietly widening the provider or customer network scope. The present scope must instead be justified by Interface-level OSPF inspection shows the local circuit attached to area 0.0.0.1 while the peer expects area 0.0.0.0 on the same numbered link.
The approval decision should consider Interface-level OSPF inspection shows the local circuit attached to area 0.0.0.1 while the peer expects area 0.0.0.0 on the same numbered link. The specific proposal is: Approve only the bounded change (Validate the inter-router interface, area design and active configuration, then align the intended area membership under the appropriate OSPF instance.) after independently checking (Both routers progress to the expected full adjacency and the correct link-state routes appear without shifting unrelated interfaces into area zero.), without quietly widening the provider or customer network scope. Its measurable outcome is: Both routers progress to the expected full adjacency and the correct link-state routes appear without shifting unrelated interfaces into area zero.
Question 61
A fictional Junos service-provider engineer encounters this scenario: Two Junos aggregation routers exchange IP packets but their OSPF adjacency never advances after an automated timer rollout. Distinguishing evidence: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. Which specific bounded Junos routing or switching correction best addresses this service-provider issue?
Answer and Explanation
Correct Answer: D
Another proposed action is: Validate the inter-router interface, area design and active configuration, then align the intended area membership under the appropriate OSPF instance. That does not directly address the observed condition: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. The more targeted correction is: Check approved liveness requirements and align the interface hello and dead parameters on both adjacent devices before committing.
Another proposed action is: Inspect applicable BGP best-path attributes and local routing policy before modifying any IGP metric or neighboring AS path. It targets a different dependency; the evidence here is OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.
Another option proposes: Repeat routing and operational tests explicitly in the correct customer instance and investigate any actual gap without changing global routing. The specific correction is: Check approved liveness requirements and align the interface hello and dead parameters on both adjacent devices before committing. The deciding evidence is: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.
The observed condition is: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. This calls for the scoped change: Check approved liveness requirements and align the interface hello and dead parameters on both adjacent devices before committing. The acceptance measure is: The neighbor remains full through several monitored intervals, while routing reconverges predictably on a controlled link loss.
Question 62
A fictional Junos service-provider engineer encounters this scenario: Two Junos aggregation routers exchange IP packets but their OSPF adjacency never advances after an automated timer rollout. Which observed operational evidence most strongly isolates the actual protocol or forwarding condition?
Answer and Explanation
Correct Answer: C
This other option describes: OSPF database output includes relevant link-state information, whereas the active route table prefers a more specific or otherwise preferred competing route for the destination. The problem to explain is different: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.
Another proposed finding is: The script performs route and ping checks in the default table while the customer interface and its OSPF learned routes live in an isolated routing instance. It is not the recorded discriminator, which is OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.
Consider this evidence: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. The applicable explanation is: OSPF neighbors require compatible interface-level parameters, including timing behavior. The matching response is: Check approved liveness requirements and align the interface hello and dead parameters on both adjacent devices before committing.
Another alternative would address the IS-IS database contains distinct reachability TLV content while the operational command targets only the inet address family rather than inet6 as decisive. The actual evidence in this case is OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.
Question 63
A fictional Junos service-provider engineer encounters this scenario: Two Junos aggregation routers exchange IP packets but their OSPF adjacency never advances after an automated timer rollout. Distinguishing evidence: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. Which Junos networking principle best explains the relevant engineering decision?
Answer and Explanation
Correct Answer: B
The competing option invokes: OSPF broadcast networks use DR and BDR election to reduce adjacency overhead. Evidence for this case: The interface is a broadcast multiaccess network with elected DR and BDR and the newcomer has low priority; neighbor output shows full adjacency to elected routers. The present evidence is: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. The case-relevant principle is: OSPF neighbors require compatible interface-level parameters, including timing behavior.
OSPF neighbors require compatible interface-level parameters, including timing behavior. This distinction accounts for OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned; another unrelated mechanism would not address the same condition.
A different principle is: OSPF link-state advertisement data and active routing-table installation are different diagnostic layers. Evidence for this case: OSPF database output includes relevant link-state information, whereas the active route table prefers a more specific or otherwise preferred competing route for the destination. The present evidence, however, is OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. The relevant rule is: OSPF neighbors require compatible interface-level parameters, including timing behavior.
This alternative invokes: Routing instances and RIB groups require explicit route import and forwarding boundaries. Evidence for this case: Route inspection shows several tenant networks imported into a shared routing table through a broad RIB group rather than the single approved resolver route. The governing distinction for the recorded case is OSPF neighbors require compatible interface-level parameters, including timing behavior.
Question 64
A fictional Junos service-provider engineer encounters this scenario: Two Junos aggregation routers exchange IP packets but their OSPF adjacency never advances after an automated timer rollout. Intended bounded correction: Check approved liveness requirements and align the interface hello and dead parameters on both adjacent devices before committing. Which independently verifiable test best demonstrates the intended correction worked?
Answer and Explanation
Correct Answer: A
The expected outcome is the neighbor remains full through several monitored intervals, while routing reconverges predictably on a controlled link loss. It links the scoped action to the documented condition: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.
Passing that test would not establish resolution of the stated issue. The relevant proof is: The neighbor remains full through several monitored intervals, while routing reconverges predictably on a controlled link loss.
That result would assess another condition: The chosen path matches the documented policy intent and forwarding probes follow the selected healthy upstream. The correct criterion is directly linked to the finding: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.
Another proposed result is: The observed DR and BDR remain legitimate and all routers learn correct routes without forcing unnecessary full mesh adjacencies. It would not independently establish the required outcome: The neighbor remains full through several monitored intervals, while routing reconverges predictably on a controlled link loss.
Question 65
A fictional Junos service-provider engineer encounters this scenario: Two Junos aggregation routers exchange IP packets but their OSPF adjacency never advances after an automated timer rollout. Distinguishing evidence: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. Which material service-availability, routing, switching or security risk most directly needs control?
Answer and Explanation
Correct Answer: D
This limitation concerns another setting: Altering link metrics to force a DIS outcome can reroute unrelated customer traffic without changing election priority. The observed facts here make a different caution decisive: Changing every interface timer to match one link can create unnecessary churn and route instability elsewhere.
Another caution is: Debugging only the global table can prompt unintended configuration changes to an otherwise healthy customer VPN. The key risk in this case is: Changing every interface timer to match one link can create unnecessary churn and route instability elsewhere.
Another emphasis concerns: Confusing LSDB inventory with installed active forwarding entries can cause incorrect policy changes. The current change is Check approved liveness requirements and align the interface hello and dead parameters on both adjacent devices before committing; the material limitation is Changing every interface timer to match one link can create unnecessary churn and route instability elsewhere.
A necessary safeguard is: Changing every interface timer to match one link can create unnecessary churn and route instability elsewhere. The proposed correction remains: Check approved liveness requirements and align the interface hello and dead parameters on both adjacent devices before committing.
Question 66
A fictional Junos service-provider engineer encounters this scenario: Two Junos aggregation routers exchange IP packets but their OSPF adjacency never advances after an automated timer rollout. Distinguishing evidence: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. Which focused investigation is the most useful before modifying the network configuration?
Answer and Explanation
Correct Answer: A
The current finding is OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. The specific pre-change check is: Compare active Junos routing, protocol and forwarding displays with this differentiating observed evidence: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. Use it to distinguish the problem from an unrelated symptom.
That check concerns a different signal: Compare active Junos routing, protocol and forwarding displays with this differentiating observed evidence: The interface is a broadcast multiaccess network with elected DR and BDR and the newcomer has low priority; neighbor output shows full adjacency to elected routers. The case-relevant check is: Compare active Junos routing, protocol and forwarding displays with this differentiating observed evidence: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.
Another check would compare active Junos routing, protocol and forwarding displays with this differentiating observed evidence: OSPF database output includes relevant link-state information, whereas the active route table prefers a more specific or otherwise preferred competing route for the destination. The case observation to isolate is OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. The focused check here is: Compare active Junos routing, protocol and forwarding displays with this differentiating observed evidence: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.
Another investigation would compare active Junos routing, protocol and forwarding displays with this differentiating observed evidence: The neighboring router advertises a different source address from the one in the local configured BGP neighbor statement and logs show connection attempts to the obsolete IP. It does not directly establish the reported condition: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.
Question 67
A fictional Junos service-provider engineer encounters this scenario: Two Junos aggregation routers exchange IP packets but their OSPF adjacency never advances after an automated timer rollout. Distinguishing evidence: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. Which controlled operational implementation sequence best protects the related provider service?
Answer and Explanation
Correct Answer: B
Another possible combination is: First verify the observed failure (OSPF database output includes relevant link-state information, whereas the active route table prefers a more specific or otherwise preferred competing route for the destination.); review and authorize the bounded correction (Compare link-state database reachability with route calculation, preference and active forwarding selection before modifying advertisement filters.); then independently verify the intended outcome (Database entries and active route selection are explainable, and probes follow the intended next hop without falsely requiring every LSA to be an active route.) before production rollout. The current record instead supports Check approved liveness requirements and align the interface hello and dead parameters on both adjacent devices before committing, verified by the neighbor remains full through several monitored intervals, while routing reconverges predictably on a controlled link loss.
The starting point is OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. The proposed action and its separate check are Check approved liveness requirements and align the interface hello and dead parameters on both adjacent devices before committing and the neighbor remains full through several monitored intervals, while routing reconverges predictably on a controlled link loss, respectively.
Another action-and-check pairing is: First verify the observed failure (The script performs route and ping checks in the default table while the customer interface and its OSPF learned routes live in an isolated routing instance.); review and authorize the bounded correction (Repeat routing and operational tests explicitly in the correct customer instance and investigate any actual gap without changing global routing.); then independently verify the intended outcome (Route displays and sourced tests from the correct instance explain end-to-end reachability and isolate the false default-table alarm.) before production rollout. The evidence here is OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. The required action and proof are Check approved liveness requirements and align the interface hello and dead parameters on both adjacent devices before committing and the neighbor remains full through several monitored intervals, while routing reconverges predictably on a controlled link loss.
An alternative plan is: First verify the observed failure (IS-IS topology output reflects the new interface cost and SPF paths differ, while link utilization counters align with the changed shortest path.); review and authorize the bounded correction (Compare level-specific route metrics and approved traffic-engineering intent, then restore or adjust the scoped metric with a measured failover plan.); then independently verify the intended outcome (Representative destinations use the intended ring path and link utilization remains within the approved operational envelope.) before production rollout. It does not test the case-specific condition: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.
Question 68
A fictional Junos service-provider engineer encounters this scenario: Two Junos aggregation routers exchange IP packets but their OSPF adjacency never advances after an automated timer rollout. Distinguishing evidence: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. Which set of evidence, limited change and independent validation best justifies authorization?
Answer and Explanation
Correct Answer: B
Another approval action is: Observed evidence (Interface-level OSPF inspection shows the local circuit attached to area 0.0.0.1 while the peer expects area 0.0.0.0 on the same numbered link.), limited correction (Validate the inter-router interface, area design and active configuration, then align the intended area membership under the appropriate OSPF instance.), independently measurable result (Both routers progress to the expected full adjacency and the correct link-state routes appear without shifting unrelated interfaces into area zero.). The relevant evidence and acceptance are OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned and the neighbor remains full through several monitored intervals, while routing reconverges predictably on a controlled link loss, respectively.
The approval decision should consider OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. The specific proposal is: Observed evidence (OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.), limited correction (Check approved liveness requirements and align the interface hello and dead parameters on both adjacent devices before committing.), independently measurable result (The neighbor remains full through several monitored intervals, while routing reconverges predictably on a controlled link loss.). Its measurable outcome is: The neighbor remains full through several monitored intervals, while routing reconverges predictably on a controlled link loss.
An alternative release decision is: Observed evidence (Routing instance views show the source prefix active, while OSPF export policy counters show its attributes failing the allowed route term.), limited correction (Review the OSPF export policy and prefix scope, then explicitly permit only the approved external destination while preserving other route exclusions.), independently measurable result (Neighbor route views receive the approved external prefix and unrelated tenant networks remain unadvertised.). It does not match the current change: Check approved liveness requirements and align the interface hello and dead parameters on both adjacent devices before committing.
Another approval action is: Observed evidence (BGP announcements still include the aggregate prefix but the route table no longer contains the former constituent access path and a probe to that branch fails.), limited correction (Inspect active contributing routes and the aggregation policy, then choose a scoped summary advertisement and appropriate blackhole safeguards that reflect verified forwarding behavior.), independently measurable result (Neighbor route reception and end-to-end reachability tests demonstrate the intended covering advertisement without incorrectly promising restored access to the failed branch.). The relevant evidence and acceptance are OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned and the neighbor remains full through several monitored intervals, while routing reconverges predictably on a controlled link loss, respectively.
Question 69
A fictional Junos service-provider engineer encounters this scenario: Two Junos aggregation routers exchange IP packets but their OSPF adjacency never advances after an automated timer rollout. Distinguishing evidence: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. If the change fails its expected acceptance test, which controlled recovery approach is most appropriate?
Answer and Explanation
Correct Answer: B
Another option proposes: Pause changes, preserve the differentiating evidence (Routing instance views show the source prefix active, while OSPF export policy counters show its attributes failing the allowed route term.), restore the last approved safe network state and reassess ospf import policy blocks a needed external route. Its assumptions differ from the observed failure; the appropriate recovery is: Pause changes, preserve the differentiating evidence (OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.), restore the last approved safe network state and reassess hello and dead interval mismatch causes ospf neighbor instability.
If the change fails acceptance, the bounded recovery is: Pause changes, preserve the differentiating evidence (OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.), restore the last approved safe network state and reassess hello and dead interval mismatch causes ospf neighbor instability. The case-specific risk is Changing every interface timer to match one link can create unnecessary churn and route instability elsewhere. The original evidence remains: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.
Another recovery route would pause changes, preserve the differentiating evidence (Operational IS-IS output shows compatible physical interfaces but inconsistent enabled protocol levels and no common level adjacency.), restore the last approved safe network state and reassess is-is level configuration prevents adjacency. It does not preserve the condition of this case: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. The bounded fallback is: Pause changes, preserve the differentiating evidence (OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.), restore the last approved safe network state and reassess hello and dead interval mismatch causes ospf neighbor instability.
Another option proposes: Pause changes, preserve the differentiating evidence (OSPF database output includes relevant link-state information, whereas the active route table prefers a more specific or otherwise preferred competing route for the destination.), restore the last approved safe network state and reassess single-area lsa information is not visible as an installed route. Its assumptions differ from the observed failure; the appropriate recovery is: Pause changes, preserve the differentiating evidence (OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.), restore the last approved safe network state and reassess hello and dead interval mismatch causes ospf neighbor instability.
Question 70
A fictional Junos service-provider engineer encounters this scenario: Two Junos aggregation routers exchange IP packets but their OSPF adjacency never advances after an automated timer rollout. Distinguishing evidence: OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned. Which bounded approval scope avoids unintended changes to other provider or customer services?
Answer and Explanation
Correct Answer: D
Another proposed approval would approve only the bounded change (Apply a precise export filter and route-policy tests for public prefixes, then confirm rejected customer-only routes stay internal.) after independently checking (Upstream advertised-route output contains only approved prefixes and the private customer destination remains available in its intended instance.), without quietly widening the provider or customer network scope. The present scope must instead be justified by OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.
A separate release decision would approve only the bounded change (Validate the inter-router interface, area design and active configuration, then align the intended area membership under the appropriate OSPF instance.) after independently checking (Both routers progress to the expected full adjacency and the correct link-state routes appear without shifting unrelated interfaces into area zero.), without quietly widening the provider or customer network scope. It does not match the current change: Check approved liveness requirements and align the interface hello and dead parameters on both adjacent devices before committing.
An alternative approval would approve only the bounded change (Compare link-state database reachability with route calculation, preference and active forwarding selection before modifying advertisement filters.) after independently checking (Database entries and active route selection are explainable, and probes follow the intended next hop without falsely requiring every LSA to be an active route.), without quietly widening the provider or customer network scope. The relevant evidence and acceptance are OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned and the neighbor remains full through several monitored intervals, while routing reconverges predictably on a controlled link loss, respectively.
The change-control boundary is: Approve only the bounded change (Check approved liveness requirements and align the interface hello and dead parameters on both adjacent devices before committing.) after independently checking (The neighbor remains full through several monitored intervals, while routing reconverges predictably on a controlled link loss.), without quietly widening the provider or customer network scope. The evidence for this scope is OSPF neighbor and interface details reveal different hello and dead intervals on the directly connected segment even though addresses and area are aligned.
Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests
- Juniper JN0-364 Practice Test 5 - 10 Questions (Last Reviewed 14-Nov-2026)
- Juniper JN0-364 Practice Test 6 - 10 Questions (Last Reviewed 13-Nov-2026)
- Juniper JN0-364 Practice Test 7 - 10 Questions (Last Reviewed 12-Nov-2026)
- Juniper JN0-364 Practice Test 8 - 10 Questions (Last Reviewed 11-Nov-2026)
- Juniper JN0-364 Practice Test 9 - 10 Questions (Last Reviewed 10-Nov-2026)