Pass Juniper JN0-364 Exam in First Attempt Guaranteed!
Get 100% Latest Exam Questions, Accurate & Verified Answers!
30 Days Free Updates, Instant Download!
Juniper JN0-364 Practice Test 34
Question 330
A fictional Junos service-provider engineer encounters this scenario: A core provider provisions an RSVP LSP around a crowded ring but the operational path still traverses an unavailable reservation hop. Distinguishing evidence: RSVP session state and explicit path display show an outdated strict hop, while IGP reachability has already moved to a different core next hop. Which bounded approval scope avoids unintended changes to other provider or customer services?
Answer and Explanation
Correct Answer: B
A separate release decision would approve only the bounded change (Use LSP-aware OAM and node label-table checks at the actual affected hop, while retaining separate underlay reachability evidence.) after independently checking (The MPLS-aware path test and customer service probes agree on a working labeled route without masking unresolved transport problems.), without quietly widening the provider or customer network scope. It does not match the current change: Compare reserved path constraints and actual underlay topology, then update the approved explicit route and resource availability before signaling again.
The change-control boundary is: Approve only the bounded change (Compare reserved path constraints and actual underlay topology, then update the approved explicit route and resource availability before signaling again.) after independently checking (The RSVP LSP establishes on a feasible approved path and measured forwarding follows its effective label-switched path.), without quietly widening the provider or customer network scope. The evidence for this scope is RSVP session state and explicit path display show an outdated strict hop, while IGP reachability has already moved to a different core next hop.
Another proposed approval would approve only the bounded change (Verify reachable IPv4 tunnel endpoints, permitted encapsulation and the specific IPv6 routing path before correcting endpoint configuration.) after independently checking (Encapsulated IPv6 traffic reaches the remote island with expected IPv4 outer endpoints and a tested return route.), without quietly widening the provider or customer network scope. The present scope must instead be justified by RSVP session state and explicit path display show an outdated strict hop, while IGP reachability has already moved to a different core next hop.
A separate release decision would approve only the bounded change (Confirm expected label advertisement and pop operation at the penultimate hop rather than forcing unnecessary labels through every device.) after independently checking (Captured traffic and destination forwarding demonstrate correct reachability with expected label disposition at each hop.), without quietly widening the provider or customer network scope. It does not match the current change: Compare reserved path constraints and actual underlay topology, then update the approved explicit route and resource availability before signaling again.
Question 331
A fictional Junos service-provider engineer encounters this scenario: A backbone operator sees an active inet destination route and concludes an MPLS traffic-engineered flow is working although customer packets stop at an intermediate hop. Distinguishing evidence: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. Which specific bounded Junos routing or switching correction best addresses this service-provider issue?
Answer and Explanation
Correct Answer: B
Another proposed action is: Inspect supported SR-MPLS advertisement, segment routing global block assumptions and underlay route consistency before changing the planned transport policy. That does not directly address the observed condition: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. The more targeted correction is: Inspect the label forwarding information base, push-swap-pop behavior and corresponding tunnel state on each relevant hop.
The evidence is the route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. The relevant principle is that MPLS forwarding uses label-specific information and operations alongside underlying routing resolution. The correction is: Inspect the label forwarding information base, push-swap-pop behavior and corresponding tunnel state on each relevant hop. The separate success check is: The expected label entry and forwarding action appear at the designated hop and end-to-end customer traffic crosses the intended LSP.
Another option proposes: Verify label distribution source, FEC identity and session state on adjacent routers, and correct the scoped label protocol fault through normal change control. The specific correction is: Inspect the label forwarding information base, push-swap-pop behavior and corresponding tunnel state on each relevant hop. The deciding evidence is: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
That alternative concerns: Correct the remote-endpoint underlay route so it remains independent of the GRE inner route, then validate inner and outer forwarding separately. The relevant evidence is the route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. The corresponding fix is: Inspect the label forwarding information base, push-swap-pop behavior and corresponding tunnel state on each relevant hop.
Question 332
A fictional Junos service-provider engineer encounters this scenario: A backbone operator sees an active inet destination route and concludes an MPLS traffic-engineered flow is working although customer packets stop at an intermediate hop. Which observed operational evidence most strongly isolates the actual protocol or forwarding condition?
Answer and Explanation
Correct Answer: A
Consider this evidence: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. The applicable explanation is: MPLS forwarding uses label-specific information and operations alongside underlying routing resolution. The matching response is: Inspect the label forwarding information base, push-swap-pop behavior and corresponding tunnel state on each relevant hop.
Another alternative would address the penultimate node advertises implicit-null behavior and forwarding views show a legitimate penultimate-hop-pop operation for the relevant LSP as decisive. The actual evidence in this case is the route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
This other option describes: IGP reachability information contains the router identifiers while SR-specific label advertisements or local SID state do not match the expected segment routing configuration. The problem to explain is different: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
Another proposed finding is: Underlay connectivity works and GRE endpoints match, yet packet captures show oversized encapsulated traffic and path MTU feedback being dropped by a filter. It is not the recorded discriminator, which is the route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
Question 333
A fictional Junos service-provider engineer encounters this scenario: A backbone operator sees an active inet destination route and concludes an MPLS traffic-engineered flow is working although customer packets stop at an intermediate hop. Distinguishing evidence: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. Which Junos networking principle best explains the relevant engineering decision?
Answer and Explanation
Correct Answer: C
A different principle is: SR-MPLS needs consistent segment information and forwarding entries coordinated with the underlay IGP. Evidence for this case: IGP reachability information contains the router identifiers while SR-specific label advertisements or local SID state do not match the expected segment routing configuration. The present evidence, however, is the route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. The relevant rule is: MPLS forwarding uses label-specific information and operations alongside underlying routing resolution.
This alternative invokes: The tunnel transport endpoint route must not depend recursively on the same tunnel it enables. Evidence for this case: The route to the GRE remote destination shows the tunnel itself as next hop instead of an ordinary physical underlay path, and decapsulation counters stop increasing. The governing distinction for the recorded case is MPLS forwarding uses label-specific information and operations alongside underlying routing resolution.
The observed evidence is: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. The governing principle is: MPLS forwarding uses label-specific information and operations alongside underlying routing resolution. Consequently, the targeted action is: Inspect the label forwarding information base, push-swap-pop behavior and corresponding tunnel state on each relevant hop.
That principle concerns another fact pattern: MPLS label stack handling may include penultimate-hop popping as part of legitimate forwarding. Evidence for this case: The penultimate node advertises implicit-null behavior and forwarding views show a legitimate penultimate-hop-pop operation for the relevant LSP. Here the key fact is: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
Question 334
A fictional Junos service-provider engineer encounters this scenario: A backbone operator sees an active inet destination route and concludes an MPLS traffic-engineered flow is working although customer packets stop at an intermediate hop. Intended bounded correction: Inspect the label forwarding information base, push-swap-pop behavior and corresponding tunnel state on each relevant hop. Which independently verifiable test best demonstrates the intended correction worked?
Answer and Explanation
Correct Answer: C
That result would assess another condition: Node SID and relevant label entries agree across the intended nodes and measured transport follows the computed shortest path. The correct criterion is directly linked to the finding: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
Another proposed result is: Neighbor discovery and route displays resolve through the correct active interface and IPv6 service probes work over the approved path. It would not independently establish the required outcome: The expected label entry and forwarding action appear at the designated hop and end-to-end customer traffic crosses the intended LSP.
The expected outcome is the expected label entry and forwarding action appear at the designated hop and end-to-end customer traffic crosses the intended LSP. It links the scoped action to the documented condition: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
Passing that test would not establish resolution of the stated issue. The relevant proof is: The expected label entry and forwarding action appear at the designated hop and end-to-end customer traffic crosses the intended LSP.
Question 335
A fictional Junos service-provider engineer encounters this scenario: A backbone operator sees an active inet destination route and concludes an MPLS traffic-engineered flow is working although customer packets stop at an intermediate hop. Distinguishing evidence: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. Which material service-availability, routing, switching or security risk most directly needs control?
Answer and Explanation
Correct Answer: D
This limitation concerns another setting: A reachable IP destination does not prove that the MPLS labeled data path has an active next-hop binding. The observed facts here make a different caution decisive: Only checking ordinary IPv4 routes can overlook missing swap or pop operations on a labeled path.
Another caution is: Ignoring encapsulation overhead can create hard-to-diagnose selective loss despite a nominally up tunnel interface. The key risk in this case is: Only checking ordinary IPv4 routes can overlook missing swap or pop operations on a labeled path.
Another emphasis concerns: A valid IGP route alone is not proof that an SR-MPLS data plane is programmed consistently across the area. The current change is Inspect the label forwarding information base, push-swap-pop behavior and corresponding tunnel state on each relevant hop; the material limitation is Only checking ordinary IPv4 routes can overlook missing swap or pop operations on a labeled path.
Only checking ordinary IPv4 routes can overlook missing swap or pop operations on a labeled path. That boundary protects the documented change, Inspect the label forwarding information base, push-swap-pop behavior and corresponding tunnel state on each relevant hop, from introducing an unrelated problem.
Question 336
A fictional Junos service-provider engineer encounters this scenario: A backbone operator sees an active inet destination route and concludes an MPLS traffic-engineered flow is working although customer packets stop at an intermediate hop. Distinguishing evidence: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. Which focused investigation is the most useful before modifying the network configuration?
Answer and Explanation
Correct Answer: C
Another investigation would compare active Junos routing, protocol and forwarding displays with this differentiating observed evidence: Tunnel interface and IPv4 underlay checks show an obsolete remote endpoint while the IPv6 routes point toward the tunnel logical interface. It does not directly establish the reported condition: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
That check concerns a different signal: Compare active Junos routing, protocol and forwarding displays with this differentiating observed evidence: RSVP session state and explicit path display show an outdated strict hop, while IGP reachability has already moved to a different core next hop. The case-relevant check is: Compare active Junos routing, protocol and forwarding displays with this differentiating observed evidence: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
The pre-change check should compare active Junos routing, protocol and forwarding displays with this differentiating observed evidence: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. That check directly concerns the route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
Another investigation would compare active Junos routing, protocol and forwarding displays with this differentiating observed evidence: Label binding and forwarding entries on adjacent devices show inconsistent outgoing and expected incoming values for the affected path segment. It does not directly establish the reported condition: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
Question 337
A fictional Junos service-provider engineer encounters this scenario: A backbone operator sees an active inet destination route and concludes an MPLS traffic-engineered flow is working although customer packets stop at an intermediate hop. Distinguishing evidence: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. Which controlled operational implementation sequence best protects the related provider service?
Answer and Explanation
Correct Answer: A
The case evidence indicates: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. Apply the scoped action: Inspect the label forwarding information base, push-swap-pop behavior and corresponding tunnel state on each relevant hop. Confirm its effect independently: The expected label entry and forwarding action appear at the designated hop and end-to-end customer traffic crosses the intended LSP.
An alternative plan is: First verify the observed failure (RSTP operational detail shows the new attachment advertising superior BPDUs and becoming root instead of the designated provider bridge.); review and authorize the bounded correction (Verify the intended root and edge-port topology, then apply supported root protection on the authorized boundary and restore correct bridge priority.); then independently verify the intended outcome (The provider bridge remains legitimate root and a controlled superior-BPDU test is contained without permanent loop formation.) before production rollout. It does not test the case-specific condition: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
Another possible combination is: First verify the observed failure (Label binding and forwarding entries on adjacent devices show inconsistent outgoing and expected incoming values for the affected path segment.); review and authorize the bounded correction (Verify label distribution source, FEC identity and session state on adjacent routers, and correct the scoped label protocol fault through normal change control.); then independently verify the intended outcome (The neighboring label bindings and forwarding operations agree and both control-plane and data-plane path verification succeed.) before production rollout. The current record instead supports Inspect the label forwarding information base, push-swap-pop behavior and corresponding tunnel state on each relevant hop, verified by the expected label entry and forwarding action appear at the designated hop and end-to-end customer traffic crosses the intended LSP.
Another potential sequence is: First verify the observed failure (IGP reachability information contains the router identifiers while SR-specific label advertisements or local SID state do not match the expected segment routing configuration.); review and authorize the bounded correction (Inspect supported SR-MPLS advertisement, segment routing global block assumptions and underlay route consistency before changing the planned transport policy.); then independently verify the intended outcome (Node SID and relevant label entries agree across the intended nodes and measured transport follows the computed shortest path.) before production rollout. It has no direct link to the distinguishing evidence: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
Question 338
A fictional Junos service-provider engineer encounters this scenario: A backbone operator sees an active inet destination route and concludes an MPLS traffic-engineered flow is working although customer packets stop at an intermediate hop. Distinguishing evidence: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. Which set of evidence, limited change and independent validation best justifies authorization?
Answer and Explanation
Correct Answer: D
Another approval action is: Observed evidence (MSTP instance membership and region parameters show the second VLAN mapped into the first spanning-tree instance and mismatched neighboring regional configuration.), limited correction (Confirm the authorized MSTP region, instance mappings and topology design, then align the relevant VLAN-to-instance definitions across participants.), independently measurable result (Per-instance operational port states match approved paths and both service VLAN groups retain loop-free reachability during a controlled link failure.). The relevant evidence and acceptance are the route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router and the expected label entry and forwarding action appear at the designated hop and end-to-end customer traffic crosses the intended LSP, respectively.
Another approval package concerns: Observed evidence (The underlay IP route remains present but the affected next hop lacks an expected LDP label binding and LDP adjacency has dropped.), limited correction (Check LDP session transport, adjacency and matching labeled next hops before choosing a narrow protocol or underlay correction.), independently measurable result (LDP neighbors and label bindings recover for the intended FEC and payload forwarding resumes over the authorized LSP.). The present scope must instead be justified by the route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
An alternative release decision is: Observed evidence (Ordinary ping succeeds, but an MPLS LSP operational probe identifies label-path failure at a middle hop while service traffic drops.), limited correction (Use LSP-aware OAM and node label-table checks at the actual affected hop, while retaining separate underlay reachability evidence.), independently measurable result (The MPLS-aware path test and customer service probes agree on a working labeled route without masking unresolved transport problems.). It does not match the current change: Inspect the label forwarding information base, push-swap-pop behavior and corresponding tunnel state on each relevant hop.
The bounded proposal is: Observed evidence (The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.), limited correction (Inspect the label forwarding information base, push-swap-pop behavior and corresponding tunnel state on each relevant hop.), independently measurable result (The expected label entry and forwarding action appear at the designated hop and end-to-end customer traffic crosses the intended LSP.). The separate acceptance measure remains: The expected label entry and forwarding action appear at the designated hop and end-to-end customer traffic crosses the intended LSP.
Question 339
A fictional Junos service-provider engineer encounters this scenario: A backbone operator sees an active inet destination route and concludes an MPLS traffic-engineered flow is working although customer packets stop at an intermediate hop. Distinguishing evidence: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. If the change fails its expected acceptance test, which controlled recovery approach is most appropriate?
Answer and Explanation
Correct Answer: A
A recovery option is to pause changes, preserve the differentiating evidence (The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.), restore the last approved safe network state and reassess mpls label lookup is confused with an ip route table entry. The intended change was Inspect the label forwarding information base, push-swap-pop behavior and corresponding tunnel state on each relevant hop, and acceptance must still be judged against the expected label entry and forwarding action appear at the designated hop and end-to-end customer traffic crosses the intended LSP.
Another fallback concerns pausing changes, preserve the differentiating evidence (OSPFv3 neighbor output is full but route-family-specific database and export inspection show the intended prefix absent from an approved advertisement scope.), restore the last approved safe network state and reassess ospfv3 adjacency is healthy but destination ipv6 route is missing. The current change concerns the route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
Another recovery route would pause changes, preserve the differentiating evidence (The underlay IP route remains present but the affected next hop lacks an expected LDP label binding and LDP adjacency has dropped.), restore the last approved safe network state and reassess mpls forwarding stops after an ldp adjacency fails. It does not preserve the condition of this case: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. The bounded fallback is: Pause changes, preserve the differentiating evidence (The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.), restore the last approved safe network state and reassess mpls label lookup is confused with an ip route table entry.
Another option proposes: Pause changes, preserve the differentiating evidence (IGP reachability information contains the router identifiers while SR-specific label advertisements or local SID state do not match the expected segment routing configuration.), restore the last approved safe network state and reassess segment routing node-sid advertisement is present but path is absent. Its assumptions differ from the observed failure; the appropriate recovery is: Pause changes, preserve the differentiating evidence (The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.), restore the last approved safe network state and reassess mpls label lookup is confused with an ip route table entry.
Question 340
A fictional Junos service-provider engineer encounters this scenario: A backbone operator sees an active inet destination route and concludes an MPLS traffic-engineered flow is working although customer packets stop at an intermediate hop. Distinguishing evidence: The route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. Which bounded approval scope avoids unintended changes to other provider or customer services?
Answer and Explanation
Correct Answer: C
Another proposed approval would approve only the bounded change (Check LDP session transport, adjacency and matching labeled next hops before choosing a narrow protocol or underlay correction.) after independently checking (LDP neighbors and label bindings recover for the intended FEC and payload forwarding resumes over the authorized LSP.), without quietly widening the provider or customer network scope. The present scope must instead be justified by the route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
A separate release decision would approve only the bounded change (Confirm the authorized MSTP region, instance mappings and topology design, then align the relevant VLAN-to-instance definitions across participants.) after independently checking (Per-instance operational port states match approved paths and both service VLAN groups retain loop-free reachability during a controlled link failure.), without quietly widening the provider or customer network scope. It does not match the current change: Inspect the label forwarding information base, push-swap-pop behavior and corresponding tunnel state on each relevant hop.
The approval decision should consider the route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router. The specific proposal is: Approve only the bounded change (Inspect the label forwarding information base, push-swap-pop behavior and corresponding tunnel state on each relevant hop.) after independently checking (The expected label entry and forwarding action appear at the designated hop and end-to-end customer traffic crosses the intended LSP.), without quietly widening the provider or customer network scope. Its measurable outcome is: The expected label entry and forwarding action appear at the designated hop and end-to-end customer traffic crosses the intended LSP.
Another proposed approval would approve only the bounded change (Confirm expected label advertisement and pop operation at the penultimate hop rather than forcing unnecessary labels through every device.) after independently checking (Captured traffic and destination forwarding demonstrate correct reachability with expected label disposition at each hop.), without quietly widening the provider or customer network scope. The present scope must instead be justified by the route table has the destination IP, but MPLS forwarding-table inspection lacks the expected incoming label operation on the affected transit router.
Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests
- Juniper JN0-364 Practice Test 32 - 10 Questions (Last Reviewed 18-Oct-2026)
- Juniper JN0-364 Practice Test 33 - 10 Questions (Last Reviewed 17-Oct-2026)
- Juniper JN0-364 Practice Test 34 - 10 Questions (Last Reviewed 16-Oct-2026)
- Juniper JN0-364 Practice Test 35 - 10 Questions (Last Reviewed 15-Oct-2026)
- Juniper JN0-364 Practice Test 36 - 10 Questions (Last Reviewed 14-Oct-2026)