Pass HP HPE7-A08 Exam in First Attempt Guaranteed!
Get 100% Latest Exam Questions, Accurate & Verified Answers!
30 Days Free Updates, Instant Download!
HP HPE7-A08 Practice Test 91
Question 900
During a switch troubleshooting session for a hospital connectivity escalation group, a fault trace confirms that a campus trunk reports normal five minute average throughput but real time application latency spikes under short bursts. The team needs a supported change with independently measurable acceptance evidence. The diagnostic trace is queue discard counters increase during bursts while average interface utilization appears low. Which intervention paired with its proof closes this exact failure?
Explanation
Correct Answer
Inspect egress queue drops and sample traffic at burst resolution to adjust buffering or capacity. Verify that burst test produces bounded queue loss and meets application latency target. Queue discard counters increase during bursts while average interface utilization appears low, and the pair must correct that exact failure.
Incorrect Answers
Burst test produces bounded queue loss and meets application latency target. To correct the reported problem, inspect egress queue drops and sample traffic at burst resolution to adjust buffering or capacity.
Pilot devices regain approved VLANs and fleet remains consistent after controlled rollout. The required validation is different: burst test produces bounded queue loss and meets application latency target. Inspect egress queue drops and sample traffic at burst resolution to adjust buffering or capacity.
Voice delay and jitter meet targets with correct queue marking under concurrent load. It would not verify that burst test produces bounded queue loss and meets application latency target. Queue discard counters increase during bursts while average interface utilization appears low, and the pair must correct that exact failure.
Question 901
In an international retailer branch deployment team, engineers discover during a new-site network commissioning review that a campus design requires local routed gateways but leaves default gateways on a remote switch that may be isolated by WAN loss. The project must protect approved network access while addressing the specific cause. The diagnostic trace is device subnet and gateway location diagram reveals every local VLAN depends on a remote link. Which intervention paired with its proof closes this exact failure?
Explanation
Correct Answer
Plan Layer 3 gateway and failure domain placement for the documented service continuity requirement. Verify that local VLAN clients retain allowed gateway and service access during simulated WAN outage. The engineering team should connect the initiating evidence device subnet and gateway location diagram reveals every local VLAN depends on a remote link to the corrective step plan Layer 3 gateway and failure domain placement for the documented service continuity requirement. Device subnet and gateway location diagram reveals every local VLAN depends on a remote link, and the pair must correct that exact failure.
Incorrect Answers
Local VLAN clients retain allowed gateway and service access during simulated WAN outage. To correct the reported problem, plan Layer 3 gateway and failure domain placement for the documented service continuity requirement. The engineering team should connect the initiating evidence device subnet and gateway location diagram reveals every local VLAN depends on a remote link to the corrective step plan Layer 3 gateway and failure domain placement for the documented service continuity requirement.
Topology tests preserve reachability without a forwarding loop during link changes. It would not verify that local VLAN clients retain allowed gateway and service access during simulated WAN outage. Device subnet and gateway location diagram reveals every local VLAN depends on a remote link, and the pair must correct that exact failure.
Tested core design meets projected port throughput resiliency and supported software requirements. The required validation is different: local VLAN clients retain allowed gateway and service access during simulated WAN outage. Plan Layer 3 gateway and failure domain placement for the documented service continuity requirement.
Question 902
During a multi-building migration plan for a regional enterprise network architecture board, a fault trace confirms that a network engineer commits to a hardware model before verifying whether the requested overlay capability exists in its targeted software release. The team needs a supported change with independently measurable acceptance evidence. Before changing equipment, which operational observation best confirms the diagnosis?
Explanation
Correct Answer
Requested overlay feature is absent from the release specific supported feature matrix for the selected SKU. A fault trace confirms that a network engineer commits to a hardware model before verifying whether the requested overlay capability exists in its targeted software release.
Incorrect Answers
“Uplink schedule specifies fiber rate and optics that the proposed switch interface cannot support” does not demonstrate what is needed when a fault trace confirms that a network engineer commits to a hardware model before verifying whether the requested overlay capability exists in its targeted software release. Requested overlay feature is absent from the release specific supported feature matrix for the selected SKU.
“Inventory shows twelve endpoint ports and a small number of routed uplinks with no modular chassis requirement” does not explain the observed failure: a fault trace confirms that a network engineer commits to a hardware model before verifying whether the requested overlay capability exists in its targeted software release. Requested overlay feature is absent from the release specific supported feature matrix for the selected SKU.
“Fabric design requires dense high speed server ports unavailable on the proposed access hardware” concerns a different part of the problem. A fault trace confirms that a network engineer commits to a hardware model before verifying whether the requested overlay capability exists in its targeted software release. Requested overlay feature is absent from the release specific supported feature matrix for the selected SKU.
Question 903
During a secured plant-to-campus refresh for a manufacturing enterprise network architect, a fault trace confirms that a migration plan inventories switches but ignores fiber type distance and transceiver interoperability at uplinks. The team needs a supported change with independently measurable acceptance evidence. Which evidence most specifically identifies this fault instead of a similar switch problem?
Explanation
Correct Answer
Bill lists short reach multimode optics for a long single mode fiber run. During a secured plant-to-campus refresh for a manufacturing enterprise network architect, a fault trace confirms that a migration plan inventories switches but ignores fiber type distance and transceiver interoperability at uplinks.
Incorrect Answers
Design acceptance contains only steady state link up tests despite a high availability requirement. During a secured plant-to-campus refresh for a manufacturing enterprise network architect, a fault trace confirms that a migration plan inventories switches but ignores fiber type distance and transceiver interoperability at uplinks. Bill lists short reach multimode optics for a long single mode fiber run.
Device budget requires more watts than the selected access stack supplies at full load. During a secured plant-to-campus refresh for a manufacturing enterprise network architect, a fault trace confirms that a migration plan inventories switches but ignores fiber type distance and transceiver interoperability at uplinks. Bill lists short reach multimode optics for a long single mode fiber run.
“Requested overlay feature is absent from the release specific supported feature matrix for the selected SKU” does not demonstrate what is needed when during a secured plant-to-campus refresh for a manufacturing enterprise network architect, a fault trace confirms that a migration plan inventories switches but ignores fiber type distance and transceiver interoperability at uplinks. Bill lists short reach multimode optics for a long single mode fiber run.
Question 904
In a multisite service assurance team, engineers discover during a routing and performance escalation that a routed network upgrade activates OSPF authentication on one switch only and adjacency goes down. The project must protect approved network access while addressing the specific cause. After remediation, which test result proves the original fault has been corrected?
Explanation
Correct Answer
Neighbor returns to full state and expected routes remain while unauthorized sessions fail. Routing protocol neighbors must agree on authentication to exchange routing state. OSPF logging reports an authentication mismatch between formerly full neighbors, which must differ from the measured post-change state.
Incorrect Answers
Routing protocol neighbors must agree on authentication to exchange routing state. OSPF logging reports an authentication mismatch between formerly full neighbors, which must differ from the measured post-change state. The proposed action “Approved emergency access policy works without granting unrestricted employee privileges” would not resolve that situation. Neighbor returns to full state and expected routes remain while unauthorized sessions fail.
The proposed step “Error rates and application transfer time normalize at agreed interface parameters” would leave the problem unresolved: oSPF logging reports an authentication mismatch between formerly full neighbors, which must differ from the measured post-change state. Neighbor returns to full state and expected routes remain while unauthorized sessions fail.
“Peer state and MAC forwarding recover with verified failover and no split brain forwarding” does not explain the observed failure: oSPF logging reports an authentication mismatch between formerly full neighbors, which must differ from the measured post-change state. Routing protocol neighbors must agree on authentication to exchange routing state. Neighbor returns to full state and expected routes remain while unauthorized sessions fail.
Question 905
During a device commissioning session for a multi-site Aruba switching engineering team, a fault trace confirms that a user facing access interface accepts bridge protocol data units and a connected unmanaged switch changes campus spanning tree. The team needs a supported change with independently measurable acceptance evidence. Which response directly addresses the reported switching issue without bypassing policy?
Explanation
Correct Answer
Apply supported BPDU protection at the intended network edge and validate recovery workflow. A newly introduced bridge advertises BPDUs into an edge port and triggers topology changes, making apply supported BPDU protection at the intended network edge and validate recovery workflow more relevant than changes aimed at neighboring features. During a device commissioning session for a multi-site Aruba switching engineering team, a fault trace confirms that a user facing access interface accepts bridge protocol data units and a connected unmanaged switch changes campus spanning tree.
Incorrect Answers
“Synchronize MST configuration name revision and VLAN instance mappings per design” does not demonstrate what is needed when a newly introduced bridge advertises BPDUs into an edge port and triggers topology changes, making apply supported BPDU protection at the intended network edge and validate recovery workflow more relevant than changes aimed at neighboring features. Apply supported BPDU protection at the intended network edge and validate recovery workflow.
Applying supported QoS classification and scheduling at the real bottleneck interface is not a direct response to the evidence: a newly introduced bridge advertises BPDUs into an edge port and triggers topology changes, making apply supported BPDU protection at the intended network edge and validate recovery workflow more relevant than changes aimed at neighboring features. Apply supported BPDU protection at the intended network edge and validate recovery workflow.
A newly introduced bridge advertises BPDUs into an edge port and triggers topology changes, making apply supported BPDU protection at the intended network edge and validate recovery workflow more relevant than changes aimed at neighboring features. Aligning permitted VLAN and native untagged tagging design at both peers alone cannot establish that the failure is corrected. Apply supported BPDU protection at the intended network edge and validate recovery workflow.
Question 906
During an AOS-CX configuration rollout for a campus access deployment group, a fault trace confirms that a newly provisioned access switch enters a Central group whose configuration permits trunk VLANs not authorized at its branch. The team needs a supported change with independently measurable acceptance evidence. What is the most defensible corrective implementation for this case?
Explanation
Correct Answer
Move or assign the device to a reviewed Central group and confirm intended configuration scope. Device configuration shows unauthorized trunk VLANs immediately after group enrollment, making move or assign the device to a reviewed Central group and confirm intended configuration scope more relevant than changes aimed at neighboring features. During an AOS-CX configuration rollout for a campus access deployment group, a fault trace confirms that a newly provisioned access switch enters a Central group whose configuration permits trunk VLANs not authorized at its branch.
Incorrect Answers
Identify configuration ownership and update the approved Central source before reconciling the device. Device configuration shows unauthorized trunk VLANs immediately after group enrollment, making move or assign the device to a reviewed Central group and confirm intended configuration scope more relevant than changes aimed at neighboring features. Move or assign the device to a reviewed Central group and confirm intended configuration scope.
Configuring supported DHCP relay on the correct gateway and verify path to authorized server addresses a separate aspect of the case. Device configuration shows unauthorized trunk VLANs immediately after group enrollment, making move or assign the device to a reviewed Central group and confirm intended configuration scope more relevant than changes aimed at neighboring features. Move or assign the device to a reviewed Central group and confirm intended configuration scope.
Verifying device identity and entitlement using supported Central onboarding procedures would not resolve the observed failure: device configuration shows unauthorized trunk VLANs immediately after group enrollment, making move or assign the device to a reviewed Central group and confirm intended configuration scope more relevant than changes aimed at neighboring features. Move or assign the device to a reviewed Central group and confirm intended configuration scope.
Question 907
In a managed LAN engineering contractor, engineers discover during a wired network handoff audit that a switch aggregation group has two physical uplinks but one partner port uses a different LACP actor mode and key. The project must protect approved network access while addressing the specific cause. Which underlying forwarding or operations principle explains the proposed change?
Explanation
Correct Answer
A port bundle depends on consistent peer negotiation not just cable presence. A switch aggregation group has two physical uplinks but one partner port uses a different LACP actor mode and key.
Incorrect Answers
Stack virtualization depends on both physical control links and consistent membership state. A switch aggregation group has two physical uplinks but one partner port uses a different LACP actor mode and key. A port bundle depends on consistent peer negotiation not just cable presence.
Network edge protection reduces the impact of unauthorized bridging devices. A switch aggregation group has two physical uplinks but one partner port uses a different LACP actor mode and key. A port bundle depends on consistent peer negotiation not just cable presence.
Device configuration drift recurs when the source of truth is not updated. A switch aggregation group has two physical uplinks but one partner port uses a different LACP actor mode and key. A port bundle depends on consistent peer negotiation not just cable presence.
Question 908
In a campus access deployment group, engineers discover during an AOS-CX configuration rollout that a user facing access interface accepts bridge protocol data units and a connected unmanaged switch changes campus spanning tree. The project must protect approved network access while addressing the specific cause. The diagnostic trace is a newly introduced bridge advertises BPDUs into an edge port and triggers topology changes. Which combined corrective action and matching validation best meets the objective?
Explanation
Correct Answer
Apply supported BPDU protection at the intended network edge and validate recovery workflow. Verify that unexpected BPDUs cause defined protection behavior without changing designated campus root. The repair is not accepted on a command-success message alone: perform apply supported BPDU protection at the intended network edge and validate recovery workflow, then measure whether unexpected BPDUs cause defined protection behavior without changing designated campus root. A newly introduced bridge advertises BPDUs into an edge port and triggers topology changes, and the pair must correct that exact failure.
Incorrect Answers
Both intended members are collecting and distributing with expected failover. It would not verify that unexpected BPDUs cause defined protection behavior without changing designated campus root. A newly introduced bridge advertises BPDUs into an edge port and triggers topology changes, and the pair must correct that exact failure.
Unexpected BPDUs cause defined protection behavior without changing designated campus root. To correct the reported problem, apply supported BPDU protection at the intended network edge and validate recovery workflow. The repair is not accepted on a command-success message alone: perform apply supported BPDU protection at the intended network edge and validate recovery workflow, then measure whether unexpected BPDUs cause defined protection behavior without changing designated campus root.
Latency sensitive traffic and business data remain within measured delay and loss targets. The required validation is different: unexpected BPDUs cause defined protection behavior without changing designated campus root. Apply supported BPDU protection at the intended network edge and validate recovery workflow.
Question 909
In a manufacturing enterprise network architect, engineers discover during a secured plant-to-campus refresh that a WAN linked campus deployment schedules simultaneous routing changes at every site without rollback boundaries. The project must protect approved network access while addressing the specific cause. The diagnostic trace is migration runbook has no per site validation gates and no known good routing configuration. Which intervention paired with its proof closes this exact failure?
Explanation
Correct Answer
Stage the switching change by failure domain with checkpoints and a tested recovery path. Verify that pilot and later site changes pass reachability tests with documented rollback completed in rehearsal. A controlled migration limits the blast radius of a failed network change. Migration runbook has no per site validation gates and no known good routing configuration, and the pair must correct that exact failure. In a manufacturing enterprise network architect, engineers discover during a secured plant-to-campus refresh that a WAN linked campus deployment schedules simultaneous routing changes at every site without rollback boundaries.
Incorrect Answers
Pilot and later site changes pass reachability tests with documented rollback completed in rehearsal. To correct the reported problem, stage the switching change by failure domain with checkpoints and a tested recovery path. A controlled migration limits the blast radius of a failed network change. In a manufacturing enterprise network architect, engineers discover during a secured plant-to-campus refresh that a WAN linked campus deployment schedules simultaneous routing changes at every site without rollback boundaries.
Topology tests preserve reachability without a forwarding loop during link changes. It would not verify that pilot and later site changes pass reachability tests with documented rollback completed in rehearsal. Migration runbook has no per site validation gates and no known good routing configuration, and the pair must correct that exact failure.
End to end link negotiates at the approved speed and meets packet loss thresholds. The required validation is different: pilot and later site changes pass reachability tests with documented rollback completed in rehearsal. Stage the switching change by failure domain with checkpoints and a tested recovery path.
Question 910
During a distribution switch deployment for a corporate voice and data network team, a fault trace confirms that an aggregation switch contains two access VLANs but has no configured routed SVI for one subnet expected to reach another. The team needs a supported change with independently measurable acceptance evidence. Before changing equipment, which operational observation best confirms the diagnosis?
Explanation
Correct Answer
Affected hosts can reach same VLAN peers but cannot ARP for the documented gateway address. Inter VLAN routing requires operational Layer 3 interfaces and correct addressing. During a distribution switch deployment for a corporate voice and data network team, a fault trace confirms that an aggregation switch contains two access VLANs but has no configured routed SVI for one subnet expected to reach another.
Incorrect Answers
The proposed step “Multicast group table ages out even though receiving hosts remain subscribed” would leave the problem unresolved: during a distribution switch deployment for a corporate voice and data network team, a fault trace confirms that an aggregation switch contains two access VLANs but has no configured routed SVI for one subnet expected to reach another. Affected hosts can reach same VLAN peers but cannot ARP for the documented gateway address.
Routing table inspection finds service prefix in a different VRF than the client gateway would not resolve the observed failure: during a distribution switch deployment for a corporate voice and data network team, a fault trace confirms that an aggregation switch contains two access VLANs but has no configured routed SVI for one subnet expected to reach another. Inter VLAN routing requires operational Layer 3 interfaces and correct addressing. Affected hosts can reach same VLAN peers but cannot ARP for the documented gateway address.
“Clients broadcast DHCP discovery locally but server receives no relayed request” does not demonstrate what is needed when during a distribution switch deployment for a corporate voice and data network team, a fault trace confirms that an aggregation switch contains two access VLANs but has no configured routed SVI for one subnet expected to reach another. Affected hosts can reach same VLAN peers but cannot ARP for the documented gateway address.
HPE Network Switching Professional (HPE7-A08) Practice Tests
- HP HPE7-A08 Practice Test 89 - 10 Questions (Last Reviewed 21-Oct-2026)
- HP HPE7-A08 Practice Test 90 - 10 Questions (Last Reviewed 20-Oct-2026)
- HP HPE7-A08 Practice Test 91 - 10 Questions (Last Reviewed 19-Oct-2026)
- HP HPE7-A08 Practice Test 92 - 10 Questions (Last Reviewed 18-Oct-2026)
- HP HPE7-A08 Practice Test 93 - 10 Questions (Last Reviewed 17-Oct-2026)
