HP HPE7-A08 Practice Test 61 - Prepaway
Practice Exams:

Pass HP HPE7-A08 Exam in First Attempt Guaranteed!

Get 100% Latest Exam Questions, Accurate & Verified Answers!

30 Days Free Updates, Instant Download!

Verified By Experts
Premium Bundle
$14.99
$74.99 $89.98

HPE7-A08 Premium Bundle


  • Premium File 172 Questions & Answers. Last update: Nov 21, 2026
  • Study Guide 794 Pages

HP HPE7-A08 Practice Test 61

Question 600

In a managed LAN engineering contractor, engineers discover during a wired network handoff audit that a user VLAN moved to a routed gateway no longer reaches the remote DHCP server because relay has not been configured. The project must protect approved network access while addressing the specific cause. The diagnostic trace is clients broadcast DHCP discovery locally but server receives no relayed request. Which intervention paired with its proof closes this exact failure?

  1. configure supported DHCP relay on the correct gateway and verify path to authorized server — verify: new clients obtain valid address prefix gateway and DNS through the intended relay
  2. align OSPF interface area and compatible adjacency parameters — verify: new clients obtain valid address prefix gateway and DNS through the intended relay
  3. identify configuration ownership and update the approved Central source before reconciling the device — verify: post synchronization device running configuration retains the authorized interface intent
  4. configure supported DHCP relay on the correct gateway and verify path to authorized server — verify: hosts in approved VLANs reach each other through intended routed gateway with policy enforcement

Explanation

Correct Answer

A:

Configure supported DHCP relay on the correct gateway and verify path to authorized server. Verify that new clients obtain valid address prefix gateway and DNS through the intended relay. Relay has not been configured. Clients broadcast DHCP discovery locally but server receives no relayed request, and the pair must correct that exact failure. In a managed LAN engineering contractor, engineers discover during a wired network handoff audit that a user VLAN moved to a routed gateway no longer reaches the remote DHCP server because relay has not been configured.

Incorrect Answers

B:

New clients obtain valid address prefix gateway and DNS through the intended relay. To correct the reported problem, configure supported DHCP relay on the correct gateway and verify path to authorized server. Relay has not been configured. In a managed LAN engineering contractor, engineers discover during a wired network handoff audit that a user VLAN moved to a routed gateway no longer reaches the remote DHCP server because relay has not been configured.

C:

Post synchronization device running configuration retains the authorized interface intent. The required validation is different: new clients obtain valid address prefix gateway and DNS through the intended relay. Configure supported DHCP relay on the correct gateway and verify path to authorized server.

D:

Hosts in approved VLANs reach each other through intended routed gateway with policy enforcement. It would not verify that new clients obtain valid address prefix gateway and DNS through the intended relay. Clients broadcast DHCP discovery locally but server receives no relayed request, and the pair must correct that exact failure.

Question 601

During a distribution switch deployment for a corporate voice and data network team, a fault trace confirms that a proposed EVPN VXLAN extension assumes endpoint segments will reach across sites before the VTEP underlay paths are available. The team needs a supported change with independently measurable acceptance evidence. Which targeted configuration or design decision should the engineer take first?

  1. validate IP underlay routing VTEP connectivity and supported overlay control plane before onboarding segments
  2. mark only verified DHCP server facing paths trusted and protect client facing ports
  3. configure approved VLAN gateway interfaces and routing policy with prefix validation
  4. configure supported DHCP relay on the correct gateway and verify path to authorized server

Explanation

Correct Answer

A:

Validate IP underlay routing VTEP connectivity and supported overlay control plane before onboarding segments. Underlay route tests show VTEP loopback addresses unreachable across the aggregation path, making validate IP underlay routing VTEP connectivity and supported overlay control plane before onboarding segments more relevant than changes aimed at neighboring features. During a distribution switch deployment for a corporate voice and data network team, a fault trace confirms that a proposed EVPN VXLAN extension assumes endpoint segments will reach across sites before the VTEP underlay paths are available.

Incorrect Answers

B:

“Mark only verified DHCP server facing paths trusted and protect client facing ports” does not demonstrate what is needed when underlay route tests show VTEP loopback addresses unreachable across the aggregation path, making validate IP underlay routing VTEP connectivity and supported overlay control plane before onboarding segments more relevant than changes aimed at neighboring features. Validate IP underlay routing VTEP connectivity and supported overlay control plane before onboarding segments.

C:

Configuring approved VLAN gateway interfaces and routing policy with prefix validation would not resolve the observed failure: underlay route tests show VTEP loopback addresses unreachable across the aggregation path, making validate IP underlay routing VTEP connectivity and supported overlay control plane before onboarding segments more relevant than changes aimed at neighboring features. Validate IP underlay routing VTEP connectivity and supported overlay control plane before onboarding segments.

D:

Configuring supported DHCP relay on the correct gateway and verify path to authorized server is not a direct response to the evidence: underlay route tests show VTEP loopback addresses unreachable across the aggregation path, making validate IP underlay routing VTEP connectivity and supported overlay control plane before onboarding segments more relevant than changes aimed at neighboring features. Validate IP underlay routing VTEP connectivity and supported overlay control plane before onboarding segments.

Question 602

In a corporate voice and data network team, engineers discover during a distribution switch deployment that a branch switch installs a static route towards a gateway that is not reachable from its chosen VLAN or VRF. The project must protect approved network access while addressing the specific cause. The diagnostic trace is route lookup shows no valid resolution toward the declared next hop. Which change-and-test combination would you approve for the affected network?

  1. correct next hop reachability and route placement in the appropriate routing context — verify: destination route resolves through the intended interface and end to end path works
  2. align OSPF interface area and compatible adjacency parameters — verify: destination route resolves through the intended interface and end to end path works
  3. establish an appropriate IGMP querier and verify group membership refresh — verify: group memberships refresh and multicast streams reach only intended receivers
  4. correct next hop reachability and route placement in the appropriate routing context — verify: authorized traffic crosses only approved routing boundaries while isolated VRFs stay separated

Explanation

Correct Answer

A:

Correct next hop reachability and route placement in the appropriate routing context. Verify that destination route resolves through the intended interface and end to end path works. Static routes depend on reachable next hops in the correct routing context. Route lookup shows no valid resolution toward the declared next hop, and the pair must correct that exact failure.

Incorrect Answers

B:

Destination route resolves through the intended interface and end to end path works. To correct the reported problem, correct next hop reachability and route placement in the appropriate routing context. Static routes depend on reachable next hops in the correct routing context.

C:

Group memberships refresh and multicast streams reach only intended receivers. The required validation is different: destination route resolves through the intended interface and end to end path works. Correct next hop reachability and route placement in the appropriate routing context.

D:

Authorized traffic crosses only approved routing boundaries while isolated VRFs stay separated. It would not verify that destination route resolves through the intended interface and end to end path works. Route lookup shows no valid resolution toward the declared next hop, and the pair must correct that exact failure.

Question 603

In an enterprise branch support unit, engineers discover during an application reachability incident that a staff member connects two active network ports through a small unmanaged bridge and the access VLAN experiences a broadcast storm. The project must protect approved network access while addressing the specific cause. What is the most defensible corrective implementation for this case?

  1. isolate the loop safely then enforce validated edge loop and BPDU protections
  2. rebalance power allocation or upgrade compliant power capacity and validate maximum demand
  3. align supported path MTU and verify fragmentation dependent application behavior
  4. correct device authorization mapping using validated identity attributes and required voice VLAN

Explanation

Correct Answer

A:

Isolate the loop safely then enforce validated edge loop and BPDU protections. Broadcast counters spike and MAC addresses flap between two access interfaces, making isolate the loop safely then enforce validated edge loop and BPDU protections more relevant than changes aimed at neighboring features.

Incorrect Answers

B:

Broadcast counters spike and MAC addresses flap between two access interfaces, making isolate the loop safely then enforce validated edge loop and BPDU protections more relevant than changes aimed at neighboring features. The proposed action “Rebalance power allocation or upgrade compliant power capacity and validate maximum demand” would not resolve that situation. Isolate the loop safely then enforce validated edge loop and BPDU protections.

C:

Aligning supported path MTU and verify fragmentation dependent application behavior leaves the reported concern untested: broadcast counters spike and MAC addresses flap between two access interfaces, making isolate the loop safely then enforce validated edge loop and BPDU protections more relevant than changes aimed at neighboring features. Isolate the loop safely then enforce validated edge loop and BPDU protections.

D:

Correct device authorization mapping using validated identity attributes and required voice VLAN. Broadcast counters spike and MAC addresses flap between two access interfaces, making isolate the loop safely then enforce validated edge loop and BPDU protections more relevant than changes aimed at neighboring features. Isolate the loop safely then enforce validated edge loop and BPDU protections.

Question 604

During an AOS-CX configuration rollout for a campus access deployment group, a fault trace confirms that a switch aggregation group has two physical uplinks but one partner port uses a different LACP actor mode and key. The team needs a supported change with independently measurable acceptance evidence. Which network engineering principle explains why the targeted fix is appropriate?

  1. DHCP broadcast traffic does not cross a routed boundary without relay support
  2. a port bundle depends on consistent peer negotiation not just cable presence
  3. MST region identity depends on consistent operational configuration
  4. stack virtualization depends on both physical control links and consistent membership state

Explanation

Correct Answer

B:

A port bundle depends on consistent peer negotiation not just cable presence. During an AOS-CX configuration rollout for a campus access deployment group, a fault trace confirms that a switch aggregation group has two physical uplinks but one partner port uses a different LACP actor mode and key.

Incorrect Answers

A:

DHCP broadcast traffic does not cross a routed boundary without relay support. During an AOS-CX configuration rollout for a campus access deployment group, a fault trace confirms that a switch aggregation group has two physical uplinks but one partner port uses a different LACP actor mode and key. A port bundle depends on consistent peer negotiation not just cable presence.

C:

MST region identity depends on consistent operational configuration. Addresses another workflow. During an AOS-CX configuration rollout for a campus access deployment group, a fault trace confirms that a switch aggregation group has two physical uplinks but one partner port uses a different LACP actor mode and key. A port bundle depends on consistent peer negotiation not just cable presence.

D:

Stack virtualization depends on both physical control links and consistent membership state. During an AOS-CX configuration rollout for a campus access deployment group, a fault trace confirms that a switch aggregation group has two physical uplinks but one partner port uses a different LACP actor mode and key. A port bundle depends on consistent peer negotiation not just cable presence.

Question 605

During a packet loss fault isolation for a regional network operations center, a fault trace confirms that a branch workstation has a narrower prefix mask than the rest of its VLAN and treats a neighboring subnet as remote. The team needs a supported change with independently measurable acceptance evidence. Which evidence most specifically identifies this fault instead of a similar switch problem?

  1. problem host route table sends same VLAN destination traffic to a gateway unlike known good hosts
  2. MSTP status identifies the uplink as an alternate discarding port while a different path forwards
  3. switch logs show RADIUS timeouts and no successful authorized authentication decision
  4. transceiver telemetry reports receiving optical power outside the supported module operating range

Explanation

Correct Answer

A:

Problem host route table sends same VLAN destination traffic to a gateway unlike known good hosts. During a packet loss fault isolation for a regional network operations center, a fault trace confirms that a branch workstation has a narrower prefix mask than the rest of its VLAN and treats a neighboring subnet as remote.

Incorrect Answers

B:

MSTP status identifies the uplink as an alternate discarding port while a different path forwards. During a packet loss fault isolation for a regional network operations center, a fault trace confirms that a branch workstation has a narrower prefix mask than the rest of its VLAN and treats a neighboring subnet as remote. Problem host route table sends same VLAN destination traffic to a gateway unlike known good hosts.

C:

“Switch logs show RADIUS timeouts and no successful authorized authentication decision” does not demonstrate what is needed when during a packet loss fault isolation for a regional network operations center, a fault trace confirms that a branch workstation has a narrower prefix mask than the rest of its VLAN and treats a neighboring subnet as remote. Problem host route table sends same VLAN destination traffic to a gateway unlike known good hosts.

D:

“Transceiver telemetry reports receiving optical power outside the supported module operating range” does not explain the observed failure: during a packet loss fault isolation for a regional network operations center, a fault trace confirms that a branch workstation has a narrower prefix mask than the rest of its VLAN and treats a neighboring subnet as remote. Problem host route table sends same VLAN destination traffic to a gateway unlike known good hosts.

Question 606

During a routing and performance escalation for a multisite service assurance team, a fault trace confirms that a staff member connects two active network ports through a small unmanaged bridge and the access VLAN experiences a broadcast storm. The team needs a supported change with independently measurable acceptance evidence. Which targeted configuration or design decision should the engineer take first?

  1. restore the port administrative state only after checking approved interface policy
  2. correct device authorization mapping using validated identity attributes and required voice VLAN
  3. isolate matching ACL entry and revise rule order to retain business permitted traffic
  4. isolate the loop safely then enforce validated edge loop and BPDU protections

Explanation

Correct Answer

D:

Isolate the loop safely then enforce validated edge loop and BPDU protections. Broadcast counters spike and MAC addresses flap between two access interfaces, making isolate the loop safely then enforce validated edge loop and BPDU protections more relevant than changes aimed at neighboring features. During a routing and performance escalation for a multisite service assurance team, a fault trace confirms that a staff member connects two active network ports through a small unmanaged bridge and the access VLAN experiences a broadcast storm.

Incorrect Answers

A:

Broadcast counters spike and MAC addresses flap between two access interfaces, making isolate the loop safely then enforce validated edge loop and BPDU protections more relevant than changes aimed at neighboring features. The proposed action “Restore the port administrative state only after checking approved interface policy” would not resolve that situation. Isolate the loop safely then enforce validated edge loop and BPDU protections.

B:

The proposed step “Correct device authorization mapping using validated identity attributes and required voice VLAN” would leave the problem unresolved: broadcast counters spike and MAC addresses flap between two access interfaces, making isolate the loop safely then enforce validated edge loop and BPDU protections more relevant than changes aimed at neighboring features. Isolate the loop safely then enforce validated edge loop and BPDU protections.

C:

Isolate matching ACL entry and revise rule order to retain business permitted traffic. Broadcast counters spike and MAC addresses flap between two access interfaces, making isolate the loop safely then enforce validated edge loop and BPDU protections more relevant than changes aimed at neighboring features. Isolate the loop safely then enforce validated edge loop and BPDU protections.

Question 607

During a packet loss fault isolation for a regional network operations center, a fault trace confirms that a switch experiences management lag and elevated CPU because repeated link transitions trigger frequent routing and MAC updates. The team needs a supported change with independently measurable acceptance evidence. What finding should an engineer use to distinguish the root cause?

  1. MST root election changes and traffic counters show a formerly blocked low capacity path now forwarding
  2. system CPU and log rate rise in parallel with repeated interface up down messages
  3. problem host route table sends same VLAN destination traffic to a gateway unlike known good hosts
  4. queue discard counters increase during bursts while average interface utilization appears low

Explanation

Correct Answer

B:

System CPU and log rate rise in parallel with repeated interface up down messages. Repeated link transitions trigger frequent routing and MAC updates rather than a generic link alarm. During a packet loss fault isolation for a regional network operations center, a fault trace confirms that a switch experiences management lag and elevated CPU because repeated link transitions trigger frequent routing and MAC updates.

Incorrect Answers

A:

“MST root election changes and traffic counters show a formerly blocked low capacity path now forwarding” does not explain the observed failure: during a packet loss fault isolation for a regional network operations center, a fault trace confirms that a switch experiences management lag and elevated CPU because repeated link transitions trigger frequent routing and MAC updates. System CPU and log rate rise in parallel with repeated interface up down messages.

C:

Repeated link transitions trigger frequent routing and MAC updates rather than a generic link alarm. During a packet loss fault isolation for a regional network operations center, a fault trace confirms that a switch experiences management lag and elevated CPU because repeated link transitions trigger frequent routing and MAC updates. The proposed action “Problem host route table sends same VLAN destination traffic to a gateway unlike known good hosts” would not resolve that situation. System CPU and log rate rise in parallel with repeated interface up down messages.

D:

The proposed step “Queue discard counters increase during bursts while average interface utilization appears low” would leave the problem unresolved: during a packet loss fault isolation for a regional network operations center, a fault trace confirms that a switch experiences management lag and elevated CPU because repeated link transitions trigger frequent routing and MAC updates. System CPU and log rate rise in parallel with repeated interface up down messages.

Question 608

During a configuration drift review for an enterprise change control council, a fault trace confirms that an operations team archives switch running configurations but never verifies that captured settings match restart persistence. The team needs a supported change with independently measurable acceptance evidence. What technical concept best distinguishes this situation from other switching failures?

  1. image maintenance should follow version compatibility and failure domain controls
  2. configuration backup quality depends on reproducibility and matching persisted state
  3. configuration standardization must account for capability differences
  4. safe network automation must tolerate uncertain delivery outcomes

Explanation

Correct Answer

B:

Configuration backup quality depends on reproducibility and matching persisted state. During a configuration drift review for an enterprise change control council, a fault trace confirms that an operations team archives switch running configurations but never verifies that captured settings match restart persistence.

Incorrect Answers

A:

Image maintenance should follow version compatibility and failure domain controls. During a configuration drift review for an enterprise change control council, a fault trace confirms that an operations team archives switch running configurations but never verifies that captured settings match restart persistence. Configuration backup quality depends on reproducibility and matching persisted state.

C:

“Configuration standardization must account for capability differences” does not explain the observed failure: during a configuration drift review for an enterprise change control council, a fault trace confirms that an operations team archives switch running configurations but never verifies that captured settings match restart persistence. Configuration backup quality depends on reproducibility and matching persisted state.

D:

“Safe network automation must tolerate uncertain delivery outcomes” concerns a different part of the problem. During a configuration drift review for an enterprise change control council, a fault trace confirms that an operations team archives switch running configurations but never verifies that captured settings match restart persistence. Configuration backup quality depends on reproducibility and matching persisted state.

Question 609

In a managed LAN engineering contractor, engineers discover during a wired network handoff audit that a multicast distribution tree receives packets on an interface not selected by unicast routing toward the source. The project must protect approved network access while addressing the specific cause. The diagnostic trace is PIM troubleshooting shows failed reverse path check and a different unicast path back to source. Which combined corrective action and matching validation best meets the objective?

  1. establish an appropriate IGMP querier and verify group membership refresh — verify: receivers obtain the stream and RPF checks pass during stable routing
  2. classify and remark traffic at a trusted boundary consistent with end to end voice QoS policy — verify: voice packets retain authorized priority while untrusted bulk traffic uses normal queues
  3. fix source route or PIM topology so multicast reverse path forwarding is valid — verify: receivers obtain the stream and RPF checks pass during stable routing
  4. fix source route or PIM topology so multicast reverse path forwarding is valid — verify: legitimate clients obtain correct leases and unauthorized DHCP offers are rejected

Explanation

Correct Answer

C:

Fix source route or PIM topology so multicast reverse path forwarding is valid. Verify that receivers obtain the stream and RPF checks pass during stable routing. PIM troubleshooting shows failed reverse path check and a different unicast path back to source, and the pair must correct that exact failure.

Incorrect Answers

A:

Receivers obtain the stream and RPF checks pass during stable routing. To correct the reported problem, fix source route or PIM topology so multicast reverse path forwarding is valid.

B:

Voice packets retain authorized priority while untrusted bulk traffic uses normal queues. The required validation is different: receivers obtain the stream and RPF checks pass during stable routing. In a managed LAN engineering contractor, engineers discover during a wired network handoff audit that a multicast distribution tree receives packets on an interface not selected by unicast routing toward the source. Fix source route or PIM topology so multicast reverse path forwarding is valid.

D:

Legitimate clients obtain correct leases and unauthorized DHCP offers are rejected. It would not verify that receivers obtain the stream and RPF checks pass during stable routing. PIM troubleshooting shows failed reverse path check and a different unicast path back to source, and the pair must correct that exact failure.

Question 610

In a university campus infrastructure team, engineers discover during a wired network topology design review that a proposed floor rollout counts Ethernet ports but not the combined power draw of phones and wireless access points. The project must protect approved network access while addressing the specific cause. Which targeted configuration or design decision should the engineer take first?

  1. compare data center capable Aruba CX platforms and supported fabric features with the leaf requirements
  2. sum expected PoE consumption and choose access hardware and feeds with tested headroom
  3. assign unique subnet and routing ownership during the implementation transition
  4. create a failover test plan for the selected redundancy technology and critical client services

Explanation

Correct Answer

B:

Sum expected PoE consumption and choose access hardware and feeds with tested headroom. Device budget requires more watts than the selected access stack supplies at full load, making sum expected PoE consumption and choose access hardware and feeds with tested headroom more relevant than changes aimed at neighboring features.

Incorrect Answers

A:

Comparing data center capable Aruba CX platforms and supported fabric features with the leaf requirements is not a direct response to the evidence: device budget requires more watts than the selected access stack supplies at full load, making sum expected PoE consumption and choose access hardware and feeds with tested headroom more relevant than changes aimed at neighboring features. Sum expected PoE consumption and choose access hardware and feeds with tested headroom.

C:

Assigning unique subnet and routing ownership during the implementation transition leaves the reported concern untested: device budget requires more watts than the selected access stack supplies at full load, making sum expected PoE consumption and choose access hardware and feeds with tested headroom more relevant than changes aimed at neighboring features. Sum expected PoE consumption and choose access hardware and feeds with tested headroom.

D:

Create a failover test plan for the selected redundancy technology and critical client services. Device budget requires more watts than the selected access stack supplies at full load, making sum expected PoE consumption and choose access hardware and feeds with tested headroom more relevant than changes aimed at neighboring features. Sum expected PoE consumption and choose access hardware and feeds with tested headroom.

HPE Network Switching Professional (HPE7-A08) Practice Tests