HP HPE7-A08 Practice Test 39 - Prepaway
Practice Exams:

Pass HP HPE7-A08 Exam in First Attempt Guaranteed!

Get 100% Latest Exam Questions, Accurate & Verified Answers!

30 Days Free Updates, Instant Download!

Verified By Experts
Premium Bundle
$14.99
$74.99 $89.98

HPE7-A08 Premium Bundle


  • Premium File 172 Questions & Answers. Last update: Nov 21, 2026
  • Study Guide 794 Pages

HP HPE7-A08 Practice Test 39

Question 380

In a regional network operations center, engineers discover during a packet loss fault isolation that an uplink flaps after new fiber installation while both peers show compatible interface speed. The project must protect approved network access while addressing the specific cause. Which evidence most specifically identifies this fault instead of a similar switch problem?

  1. port VLAN membership differs from the asset location plan and DHCP offers carry the voice subnet
  2. ACL hit counters rise for an explicit deny matching an approved client flow
  3. transceiver telemetry reports receiving optical power outside the supported module operating range
  4. interface shows administratively down rather than physical link failure

Explanation

Correct Answer

C:

Transceiver telemetry reports receiving optical power outside the supported module operating range. An uplink flaps after new fiber installation while both peers show compatible interface speed.

Incorrect Answers

A:

“Port VLAN membership differs from the asset location plan and DHCP offers carry the voice subnet” does not demonstrate what is needed when an uplink flaps after new fiber installation while both peers show compatible interface speed. Transceiver telemetry reports receiving optical power outside the supported module operating range.

B:

“ACL hit counters rise for an explicit deny matching an approved client flow” does not explain the observed failure: an uplink flaps after new fiber installation while both peers show compatible interface speed. Transceiver telemetry reports receiving optical power outside the supported module operating range.

D:

An uplink flaps after new fiber installation while both peers show compatible interface speed. The proposed action “Interface shows administratively down rather than physical link failure” would not resolve that situation. Transceiver telemetry reports receiving optical power outside the supported module operating range.

Question 381

In a managed switching services provider, engineers discover during an operational monitoring analysis that a telemetry integration sends high frequency REST queries to hundreds of switches and causes management CPU spikes. The project must protect approved network access while addressing the specific cause. What technical concept best distinguishes this situation from other switching failures?

  1. automation privileges should be limited to operations actually required
  2. configuration management must protect the secrets it transports and archives
  3. programmatic network management requires load and rate control
  4. safe network automation must tolerate uncertain delivery outcomes

Explanation

Correct Answer

C:

Programmatic network management requires load and rate control. A telemetry integration sends high frequency REST queries to hundreds of switches and causes management CPU spikes.

Incorrect Answers

A:

Automation privileges should be limited to operations actually required. A telemetry integration sends high frequency REST queries to hundreds of switches and causes management CPU spikes. Programmatic network management requires load and rate control.

B:

Configuration management must protect the secrets it transports and archives. A telemetry integration sends high frequency REST queries to hundreds of switches and causes management CPU spikes. Programmatic network management requires load and rate control.

D:

“Safe network automation must tolerate uncertain delivery outcomes” does not explain the observed failure: a telemetry integration sends high frequency REST queries to hundreds of switches and causes management CPU spikes. Programmatic network management requires load and rate control.

Question 382

In an enterprise change control council, engineers discover during a configuration drift review that a field engineer fixes one access port locally but the centralized intended configuration remains inconsistent across the group. The project must protect approved network access while addressing the specific cause. Which targeted configuration or design decision should the engineer take first?

  1. rehearse restoring compatible configurations onto spare hardware with secret handling and port mapping review
  2. apply scoped access credentials and test least privilege for the API automation identity
  3. move credentials to protected secrets storage and rotate exposed tokens before reusing automation
  4. compare running settings with approved source and reconcile emergency change through change control

Explanation

Correct Answer

D:

Compare running settings with approved source and reconcile emergency change through change control. Audit diff reveals port authorization differs from approved standardized switch baseline, making compare running settings with approved source and reconcile emergency change through change control more relevant than changes aimed at neighboring features.

Incorrect Answers

A:

Audit diff reveals port authorization differs from approved standardized switch baseline, making compare running settings with approved source and reconcile emergency change through change control more relevant than changes aimed at neighboring features. The proposed action “Rehearse restoring compatible configurations onto spare hardware with secret handling and port mapping review” would not resolve that situation. Compare running settings with approved source and reconcile emergency change through change control.

B:

Applying scoped access credentials and test least privilege for the API automation identity leaves the reported concern untested: audit diff reveals port authorization differs from approved standardized switch baseline, making compare running settings with approved source and reconcile emergency change through change control more relevant than changes aimed at neighboring features. Compare running settings with approved source and reconcile emergency change through change control.

C:

Move credentials to protected secrets storage and rotate exposed tokens before reusing automation. Audit diff reveals port authorization differs from approved standardized switch baseline, making compare running settings with approved source and reconcile emergency change through change control more relevant than changes aimed at neighboring features. Compare running settings with approved source and reconcile emergency change through change control.

Question 383

In a campus network incident response team, engineers discover during a critical wired outage investigation that a newly introduced printer uses a fixed address already assigned to a workstation and both report erratic network access. The project must protect approved network access while addressing the specific cause. After remediation, which test result proves the original fault has been corrected?

  1. interface shows operational up and permitted traffic passes without relaxing security
  2. each endpoint has a unique address and reaches the gateway without ARP churn
  3. backup scheduling or host link design meets throughput goals without unnecessary campus uplink changes
  4. link stays stable with receive levels in range and no new physical errors

Explanation

Correct Answer

B:

Each endpoint has a unique address and reaches the gateway without ARP churn. ARP tables alternate the same IP address between two distinct MAC addresses, which must differ from the measured post-change state.

Incorrect Answers

A:

“Interface shows operational up and permitted traffic passes without relaxing security” does not explain the observed failure: aRP tables alternate the same IP address between two distinct MAC addresses, which must differ from the measured post-change state. Each endpoint has a unique address and reaches the gateway without ARP churn.

C:

Backup scheduling or host link design meets throughput goals without unnecessary campus uplink changes. ARP tables alternate the same IP address between two distinct MAC addresses, which must differ from the measured post-change state. Each endpoint has a unique address and reaches the gateway without ARP churn.

D:

Link stays stable with receive levels in range and no new physical errors. ARP tables alternate the same IP address between two distinct MAC addresses, which must differ from the measured post-change state. Each endpoint has a unique address and reaches the gateway without ARP churn.

Question 384

In a multi-site Aruba switching engineering team, engineers discover during a device commissioning session that a campus services subnet is accidentally added to the wrong VRF and authorized clients cannot resolve a routed path. The project must protect approved network access while addressing the specific cause. After remediation, which test result proves the original fault has been corrected?

  1. authorized traffic crosses only approved routing boundaries while isolated VRFs stay separated
  2. validated overlay endpoints exchange permitted traffic with working underlay and control plane
  3. stack converges as the intended logical unit and surviving members preserve service during tested failure
  4. destination route resolves through the intended interface and end to end path works

Explanation

Correct Answer

A:

Authorized traffic crosses only approved routing boundaries while isolated VRFs stay separated. Routing table inspection finds service prefix in a different VRF than the client gateway, which must differ from the measured post-change state.

Incorrect Answers

B:

Validated overlay endpoints exchange permitted traffic with working underlay and control plane. Routing table inspection finds service prefix in a different VRF than the client gateway, which must differ from the measured post-change state. Authorized traffic crosses only approved routing boundaries while isolated VRFs stay separated.

C:

“Stack converges as the intended logical unit and surviving members preserve service during tested failure” does not explain the observed failure: routing table inspection finds service prefix in a different VRF than the client gateway, which must differ from the measured post-change state. Authorized traffic crosses only approved routing boundaries while isolated VRFs stay separated.

D:

Destination route resolves through the intended interface and end to end path works. Addresses another workflow. Routing table inspection finds service prefix in a different VRF than the client gateway, which must differ from the measured post-change state. Authorized traffic crosses only approved routing boundaries while isolated VRFs stay separated.

Question 385

In a campus access deployment group, engineers discover during an AOS-CX configuration rollout that a distribution layer installs two Aruba CX peers but treats them as one logical chassis without establishing supported VSX peer and keepalive design. The project must protect approved network access while addressing the specific cause. What measurable result best demonstrates recovery without creating a new access exposure?

  1. authorized test user receives intended role and policy enforcement is validated end to end
  2. validated VSX pair maintains intended dual homed connectivity through tested single peer failure
  3. an induced test alarm reaches the correct site queue with accurate device identity
  4. the actual switch appears managed in the intended organization group and site

Explanation

Correct Answer

B:

Validated VSX pair maintains intended dual homed connectivity through tested single peer failure. Redundancy plan references a shared logical control plane although switch peer configuration is absent, which must differ from the measured post-change state.

Incorrect Answers

A:

The proposed step “Authorized test user receives intended role and policy enforcement is validated end to end” would leave the problem unresolved: redundancy plan references a shared logical control plane although switch peer configuration is absent, which must differ from the measured post-change state. Validated VSX pair maintains intended dual homed connectivity through tested single peer failure.

C:

An induced test alarm reaches the correct site queue with accurate device identity. Redundancy plan references a shared logical control plane although switch peer configuration is absent, which must differ from the measured post-change state. Validated VSX pair maintains intended dual homed connectivity through tested single peer failure.

D:

“The actual switch appears managed in the intended organization group and site” does not demonstrate what is needed when redundancy plan references a shared logical control plane although switch peer configuration is absent, which must differ from the measured post-change state. Validated VSX pair maintains intended dual homed connectivity through tested single peer failure.

Question 386

In an enterprise change control council, engineers discover during a configuration drift review that a VSX distribution pair logs keepalive interruption while the data carrying inter switch link remains healthy. The project must protect approved network access while addressing the specific cause. What measurable result best demonstrates recovery without creating a new access exposure?

  1. authorized service traffic is permitted while forbidden traffic retains enforced denial
  2. fleet config audit is clean and repaired port retains correct allowed service
  3. peer health and separate keepalive reachability recover without disrupting authorized flows
  4. repaired uplink has stable counters and application packet loss meets target

Explanation

Correct Answer

C:

Peer health and separate keepalive reachability recover without disrupting authorized flows. VSX keepalive and inter switch link serve distinct failure detection roles. VSX status specifically reports keepalive lost while the peer forwarding link is operational, which must differ from the measured post-change state.

Incorrect Answers

A:

“Authorized service traffic is permitted while forbidden traffic retains enforced denial” concerns a different part of the problem. VSX status specifically reports keepalive lost while the peer forwarding link is operational, which must differ from the measured post-change state. Peer health and separate keepalive reachability recover without disrupting authorized flows.

B:

VSX keepalive and inter switch link serve distinct failure detection roles. VSX status specifically reports keepalive lost while the peer forwarding link is operational, which must differ from the measured post-change state. The proposed action “Fleet config audit is clean and repaired port retains correct allowed service” would not resolve that situation. Peer health and separate keepalive reachability recover without disrupting authorized flows.

D:

“Repaired uplink has stable counters and application packet loss meets target” does not explain the observed failure: vSX status specifically reports keepalive lost while the peer forwarding link is operational, which must differ from the measured post-change state. VSX keepalive and inter switch link serve distinct failure detection roles. Peer health and separate keepalive reachability recover without disrupting authorized flows.

Question 387

During an AOS-CX configuration rollout for a campus access deployment group, a fault trace confirms that an access engineer configures an uplink as a single untagged VLAN despite a requirement to carry several tagged services. The team needs a supported change with independently measurable acceptance evidence. Which underlying forwarding or operations principle explains the proposed change?

  1. running configuration and startup state must be made consistent
  2. centralized policy grouping is a change control boundary
  3. port VLAN mode and peer tagging must agree
  4. similar network products can use different operating systems and command models

Explanation

Correct Answer

C:

Port VLAN mode and peer tagging must agree. The repair is not accepted on a command-success message alone: perform set the correct AOS-CX interface VLAN tagging mode and validate both ends, then measure whether tagged frames for all approved VLANs traverse the uplink without introducing unauthorized VLANs. During an AOS-CX configuration rollout for a campus access deployment group, a fault trace confirms that an access engineer configures an uplink as a single untagged VLAN despite a requirement to carry several tagged services.

Incorrect Answers

A:

Running configuration and startup state must be made consistent addresses a separate aspect of the case. During an AOS-CX configuration rollout for a campus access deployment group, a fault trace confirms that an access engineer configures an uplink as a single untagged VLAN despite a requirement to carry several tagged services. Port VLAN mode and peer tagging must agree.

B:

“Centralized policy grouping is a change control boundary” does not explain the observed failure: during an AOS-CX configuration rollout for a campus access deployment group, a fault trace confirms that an access engineer configures an uplink as a single untagged VLAN despite a requirement to carry several tagged services. Port VLAN mode and peer tagging must agree.

D:

The repair is not accepted on a command-success message alone: perform set the correct AOS-CX interface VLAN tagging mode and validate both ends, then measure whether tagged frames for all approved VLANs traverse the uplink without introducing unauthorized VLANs. During an AOS-CX configuration rollout for a campus access deployment group, a fault trace confirms that an access engineer configures an uplink as a single untagged VLAN despite a requirement to carry several tagged services. The proposed action “Similar network products can use different operating systems and command models” would not resolve that situation. Port VLAN mode and peer tagging must agree.

Question 388

During a production switch lifecycle review for a telecommunications backbone operations unit, a fault trace confirms that an automation job pushes a trunk modification to every switch without checking first device outcomes. The team needs a supported change with independently measurable acceptance evidence. The diagnostic trace is automation log records the same failed trunk change applied to all network locations. Which change-and-test combination would you approve for the affected network?

  1. schedule optical path correction after validating module power thresholds and connector condition — verify: post repair optical power is in supported range and no warning events recur
  2. rehearse restoring compatible configurations onto spare hardware with secret handling and port mapping review — verify: pilot, staged rollouts and a tested rollback meet per site connectivity checks
  3. use small batch canary deployments and checkpointed reversible configuration changes — verify: pilot and sequential production upgrades preserve routing security and redundancy with tested recovery
  4. use small batch canary deployments and checkpointed reversible configuration changes — verify: pilot, staged rollouts and a tested rollback meet per site connectivity checks

Explanation

Correct Answer

D:

Use small batch canary deployments and checkpointed reversible configuration changes. Verify that pilot, staged rollouts and a tested rollback meet per site connectivity checks. Automation log records the same failed trunk change applied to all network locations, and the pair must correct that exact failure.

Incorrect Answers

A:

Post repair optical power is in supported range and no warning events recur. The required validation is different: pilot, staged rollouts and a tested rollback meet per site connectivity checks. Use small batch canary deployments and checkpointed reversible configuration changes.

B:

Pilot, staged rollouts and a tested rollback meet per site connectivity checks. To correct the reported problem, use small batch canary deployments and checkpointed reversible configuration changes.

C:

Pilot and sequential production upgrades preserve routing security and redundancy with tested recovery. It would not verify that pilot, staged rollouts and a tested rollback meet per site connectivity checks. Automation log records the same failed trunk change applied to all network locations, and the pair must correct that exact failure.

Question 389

During a multi-building migration plan for a regional enterprise network architecture board, a fault trace confirms that a campus expansion reuses an IP subnet already routed at a second location and risks ambiguous forwarding. The team needs a supported change with independently measurable acceptance evidence. Which targeted configuration or design decision should the engineer take first?

  1. compare data center capable Aruba CX platforms and supported fabric features with the leaf requirements
  2. stage the switching change by failure domain with checkpoints and a tested recovery path
  3. assign unique subnet and routing ownership during the implementation transition
  4. calculate traffic demand and plan redundant high speed uplinks before deploying the closet switches

Explanation

Correct Answer

C:

Assign unique subnet and routing ownership during the implementation transition. Subnet inventory identifies the same prefix on two independently routed interfaces, making assign unique subnet and routing ownership during the implementation transition more relevant than changes aimed at neighboring features.

Incorrect Answers

A:

Subnet inventory identifies the same prefix on two independently routed interfaces, making assign unique subnet and routing ownership during the implementation transition more relevant than changes aimed at neighboring features. Comparing data center capable Aruba CX platforms and supported fabric features with the leaf requirements alone cannot establish that the failure is corrected. Assign unique subnet and routing ownership during the implementation transition.

B:

The proposed step “Stage the switching change by failure domain with checkpoints and a tested recovery path” would leave the problem unresolved: subnet inventory identifies the same prefix on two independently routed interfaces, making assign unique subnet and routing ownership during the implementation transition more relevant than changes aimed at neighboring features. Assign unique subnet and routing ownership during the implementation transition.

D:

Calculate traffic demand and plan redundant high speed uplinks before deploying the closet switches. Subnet inventory identifies the same prefix on two independently routed interfaces, making assign unique subnet and routing ownership during the implementation transition more relevant than changes aimed at neighboring features. Assign unique subnet and routing ownership during the implementation transition.

Question 390

During a high-availability implementation meeting for a regional hospital network change group, a fault trace confirms that an engineer diagrams two aggregation switches but never validates host reachability during one device failure. The team needs a supported change with independently measurable acceptance evidence. After remediation, which test result proves the original fault has been corrected?

  1. the delivered image and hardware demonstrate all required overlay and routing functions in a lab
  2. controlled failure exercises meet convergence and packet loss service objectives
  3. measured application load stays within documented utilization and latency targets during peak periods
  4. an operator can recover configuration after intentionally disrupting production management routing

Explanation

Correct Answer

B:

Controlled failure exercises meet convergence and packet loss service objectives. Design acceptance contains only steady state link up tests despite a high availability requirement, which must differ from the measured post-change state.

Incorrect Answers

A:

“The delivered image and hardware demonstrate all required overlay and routing functions in a lab” does not explain the observed failure: design acceptance contains only steady state link up tests despite a high availability requirement, which must differ from the measured post-change state. Controlled failure exercises meet convergence and packet loss service objectives.

C:

Design acceptance contains only steady state link up tests despite a high availability requirement, which must differ from the measured post-change state. The proposed action “Measured application load stays within documented utilization and latency targets during peak periods” would not resolve that situation. Controlled failure exercises meet convergence and packet loss service objectives.

D:

The proposed step “An operator can recover configuration after intentionally disrupting production management routing” would leave the problem unresolved: design acceptance contains only steady state link up tests despite a high availability requirement, which must differ from the measured post-change state. Controlled failure exercises meet convergence and packet loss service objectives.

HPE Network Switching Professional (HPE7-A08) Practice Tests