Pass HP HPE7-A08 Exam in First Attempt Guaranteed!
Get 100% Latest Exam Questions, Accurate & Verified Answers!
30 Days Free Updates, Instant Download!
HP HPE7-A08 Practice Test 36
Question 350
During a network segmentation validation test for a municipal services switching organization, a fault trace confirms that a campus services subnet is accidentally added to the wrong VRF and authorized clients cannot resolve a routed path. The team needs a supported change with independently measurable acceptance evidence. The diagnostic trace is routing table inspection finds service prefix in a different VRF than the client gateway. Which change-and-test combination would you approve for the affected network?
Explanation
Correct Answer
Place interfaces and routes in the intended VRF and define explicit allowed inter VRF access. Verify that authorized traffic crosses only approved routing boundaries while isolated VRFs stay separated. Routing table inspection finds service prefix in a different VRF than the client gateway, and the pair must correct that exact failure.
Incorrect Answers
Authorized traffic crosses only approved routing boundaries while isolated VRFs stay separated. To correct the reported problem, place interfaces and routes in the intended VRF and define explicit allowed inter VRF access.
New clients obtain valid address prefix gateway and DNS through the intended relay. It would not verify that authorized traffic crosses only approved routing boundaries while isolated VRFs stay separated. Routing table inspection finds service prefix in a different VRF than the client gateway, and the pair must correct that exact failure.
Latency sensitive traffic and business data remain within measured delay and loss targets. The required validation is different: authorized traffic crosses only approved routing boundaries while isolated VRFs stay separated. Place interfaces and routes in the intended VRF and define explicit allowed inter VRF access.
Question 351
During a switch troubleshooting session for a hospital connectivity escalation group, a fault trace confirms that a four link aggregation runs near overload on one member although overall bundle throughput is below capacity. The team needs a supported change with independently measurable acceptance evidence. Which evidence most specifically identifies this fault instead of a similar switch problem?
Explanation
Correct Answer
One physical LACP member is heavily saturated while other members remain underused. During a switch troubleshooting session for a hospital connectivity escalation group, a fault trace confirms that a four link aggregation runs near overload on one member although overall bundle throughput is below capacity.
Incorrect Answers
“ARP tables alternate the same IP address between two distinct MAC addresses” concerns a different part of the problem. During a switch troubleshooting session for a hospital connectivity escalation group, a fault trace confirms that a four link aggregation runs near overload on one member although overall bundle throughput is below capacity. One physical LACP member is heavily saturated while other members remain underused.
During a switch troubleshooting session for a hospital connectivity escalation group, a fault trace confirms that a four link aggregation runs near overload on one member although overall bundle throughput is below capacity. The proposed action “One peer indicates negotiated full duplex while the other side shows mismatched fixed settings and errors” would not resolve that situation. One physical LACP member is heavily saturated while other members remain underused.
The proposed step “Egress priority queue counters attribute most usage to bulk flows instead of approved real time classes” would leave the problem unresolved: during a switch troubleshooting session for a hospital connectivity escalation group, a fault trace confirms that a four link aggregation runs near overload on one member although overall bundle throughput is below capacity. One physical LACP member is heavily saturated while other members remain underused.
Question 352
In a manufacturing enterprise network architect, engineers discover during a secured plant-to-campus refresh that a network engineer commits to a hardware model before verifying whether the requested overlay capability exists in its targeted software release. The project must protect approved network access while addressing the specific cause. Before changing equipment, which operational observation best confirms the diagnosis?
Explanation
Correct Answer
Requested overlay feature is absent from the release specific supported feature matrix for the selected SKU. A network engineer commits to a hardware model before verifying whether the requested overlay capability exists in its targeted software release.
Incorrect Answers
“Office topology has one wiring closet and no fabric endpoint segmentation or scale requirement” does not demonstrate what is needed when a network engineer commits to a hardware model before verifying whether the requested overlay capability exists in its targeted software release. Requested overlay feature is absent from the release specific supported feature matrix for the selected SKU.
“Inventory shows twelve endpoint ports and a small number of routed uplinks with no modular chassis requirement” concerns a different part of the problem. A network engineer commits to a hardware model before verifying whether the requested overlay capability exists in its targeted software release. Requested overlay feature is absent from the release specific supported feature matrix for the selected SKU.
A network engineer commits to a hardware model before verifying whether the requested overlay capability exists in its targeted software release. The proposed action “Uplink schedule specifies fiber rate and optics that the proposed switch interface cannot support” would not resolve that situation. Requested overlay feature is absent from the release specific supported feature matrix for the selected SKU.
Question 353
In an enterprise change control council, engineers discover during a configuration drift review that an organization treats all Aruba CX switches as identical templates despite variation in supported port interfaces and feature sets. The project must protect approved network access while addressing the specific cause. Which targeted configuration or design decision should the engineer take first?
Explanation
Correct Answer
Use validated model aware configuration profiles rather than indiscriminately copying every command. Automation pushes unsupported interface commands to a subset of switches and reports rejects, making use validated model aware configuration profiles rather than indiscriminately copying every command more relevant than changes aimed at neighboring features.
Incorrect Answers
Enforce attributable change records and time synchronized configuration audit logs. Automation pushes unsupported interface commands to a subset of switches and reports rejects, making use validated model aware configuration profiles rather than indiscriminately copying every command more relevant than changes aimed at neighboring features. Use validated model aware configuration profiles rather than indiscriminately copying every command.
Pilot supported AOS-CX release in a representative stack then stage deployment with acceptance gates. Automation pushes unsupported interface commands to a subset of switches and reports rejects, making use validated model aware configuration profiles rather than indiscriminately copying every command more relevant than changes aimed at neighboring features. Use validated model aware configuration profiles rather than indiscriminately copying every command.
Limiting polling concurrency and frequency and favor supported telemetry intervals and pagination addresses a separate aspect of the case. Automation pushes unsupported interface commands to a subset of switches and reports rejects, making use validated model aware configuration profiles rather than indiscriminately copying every command more relevant than changes aimed at neighboring features. Use validated model aware configuration profiles rather than indiscriminately copying every command.
Question 354
In a campus network incident response team, engineers discover during a critical wired outage investigation that a newly introduced printer uses a fixed address already assigned to a workstation and both report erratic network access. The project must protect approved network access while addressing the specific cause. What finding should an engineer use to distinguish the root cause?
Explanation
Correct Answer
ARP tables alternate the same IP address between two distinct MAC addresses. The repair is not accepted on a command-success message alone: perform remove the duplicate address and align allocation with the managed subnet inventory, then measure whether each endpoint has a unique address and reaches the gateway without ARP churn. A newly introduced printer uses a fixed address already assigned to a workstation and both report erratic network access.
Incorrect Answers
The repair is not accepted on a command-success message alone: perform remove the duplicate address and align allocation with the managed subnet inventory, then measure whether each endpoint has a unique address and reaches the gateway without ARP churn. A newly introduced printer uses a fixed address already assigned to a workstation and both report erratic network access. The proposed action “Problem host route table sends same VLAN destination traffic to a gateway unlike known good hosts” would not resolve that situation. ARP tables alternate the same IP address between two distinct MAC addresses.
The proposed step “Transceiver telemetry reports receiving optical power outside the supported module operating range” would leave the problem unresolved: a newly introduced printer uses a fixed address already assigned to a workstation and both report erratic network access. ARP tables alternate the same IP address between two distinct MAC addresses.
ACL hit counters rise for an explicit deny matching an approved client flow. A newly introduced printer uses a fixed address already assigned to a workstation and both report erratic network access. ARP tables alternate the same IP address between two distinct MAC addresses.
Question 355
In a multi-site Aruba switching engineering team, engineers discover during a device commissioning session that a VLAN enables multicast snooping but loses receiver memberships after a while because no active querier exists. The project must protect approved network access while addressing the specific cause. Which underlying forwarding or operations principle explains the proposed change?
Explanation
Correct Answer
IGMP snooping maintains state through membership signaling and queries. No active querier exists, as supported by the specific evidence multicast group table ages out even though receiving hosts remain subscribed, rather than a generic switching design claim. A VLAN enables multicast snooping but loses receiver memberships after a while because no active querier exists.
Incorrect Answers
“Multicast forwarding relies on a valid reverse path toward the source” concerns a different part of the problem. A VLAN enables multicast snooping but loses receiver memberships after a while because no active querier exists. IGMP snooping maintains state through membership signaling and queries.
No active querier exists, as supported by the specific evidence multicast group table ages out even though receiving hosts remain subscribed, rather than a generic switching design claim. A VLAN enables multicast snooping but loses receiver memberships after a while because no active querier exists. The proposed action “VLAN tagging and untagging must be symmetric across a trunk” would not resolve that situation. IGMP snooping maintains state through membership signaling and queries.
Running configuration and startup state must be made consistent leaves the reported concern untested: a VLAN enables multicast snooping but loses receiver memberships after a while because no active querier exists. IGMP snooping maintains state through membership signaling and queries.
Question 356
In a university campus infrastructure team, engineers discover during a wired network topology design review that an architect proposes a campus edge switch for a data center leaf fabric requiring high capacity east west forwarding. The project must protect approved network access while addressing the specific cause. What finding should an engineer use to distinguish the root cause?
Explanation
Correct Answer
Fabric design requires dense high speed server ports unavailable on the proposed access hardware. An architect proposes a campus edge switch for a data center leaf fabric requiring high capacity east west forwarding.
Incorrect Answers
Subnet inventory identifies the same prefix on two independently routed interfaces. An architect proposes a campus edge switch for a data center leaf fabric requiring high capacity east west forwarding. Fabric design requires dense high speed server ports unavailable on the proposed access hardware.
“Office topology has one wiring closet and no fabric endpoint segmentation or scale requirement” does not explain the observed failure: an architect proposes a campus edge switch for a data center leaf fabric requiring high capacity east west forwarding. Fabric design requires dense high speed server ports unavailable on the proposed access hardware.
“Selected switch datasheet lacks the expected VSF functionality while the proposal requires one logical stack” concerns a different part of the problem. An architect proposes a campus edge switch for a data center leaf fabric requiring high capacity east west forwarding. Fabric design requires dense high speed server ports unavailable on the proposed access hardware.
Question 357
During a critical wired outage investigation for a campus network incident response team, a fault trace confirms that an aggregation group includes two links but a moved cable terminates on an unrelated physical switch. The team needs a supported change with independently measurable acceptance evidence. Before changing equipment, which operational observation best confirms the diagnosis?
Explanation
Correct Answer
LACP partner system IDs disagree across the two intended bundle members. During a critical wired outage investigation for a campus network incident response team, a fault trace confirms that an aggregation group includes two links but a moved cable terminates on an unrelated physical switch.
Incorrect Answers
The proposed step “Port VLAN membership differs from the asset location plan and DHCP offers carry the voice subnet” would leave the problem unresolved: during a critical wired outage investigation for a campus network incident response team, a fault trace confirms that an aggregation group includes two links but a moved cable terminates on an unrelated physical switch. LACP partner system IDs disagree across the two intended bundle members.
MSTP status identifies the uplink as an alternate discarding port while a different path forwards. During a critical wired outage investigation for a campus network incident response team, a fault trace confirms that an aggregation group includes two links but a moved cable terminates on an unrelated physical switch. LACP partner system IDs disagree across the two intended bundle members.
“Egress priority queue counters attribute most usage to bulk flows instead of approved real time classes” does not demonstrate what is needed when during a critical wired outage investigation for a campus network incident response team, a fault trace confirms that an aggregation group includes two links but a moved cable terminates on an unrelated physical switch. LACP partner system IDs disagree across the two intended bundle members.
Question 358
During a distribution switch deployment for a corporate voice and data network team, a fault trace confirms that a technician changes an Aruba CX interface locally while its Central managed template continues to enforce an older value. The team needs a supported change with independently measurable acceptance evidence. The diagnostic trace is local edit disappears after the next Central synchronization event. Which change-and-test combination would you approve for the affected network?
Explanation
Correct Answer
Identify configuration ownership and update the approved Central source before reconciling the device. Verify that post synchronization device running configuration retains the authorized interface intent. Local edit disappears after the next Central synchronization event, and the pair must correct that exact failure. During a distribution switch deployment for a corporate voice and data network team, a fault trace confirms that a technician changes an Aruba CX interface locally while its Central managed template continues to enforce.
Incorrect Answers
Post synchronization device running configuration retains the authorized interface intent. To correct the reported problem, identify configuration ownership and update the approved Central source before reconciling the device. During a distribution switch deployment for a corporate voice and data network team, a fault trace confirms that a technician changes an Aruba CX interface locally while its Central managed template continues to enforce.
Neighbor reaches full state and agreed prefixes populate the expected routing table. The required validation is different: post synchronization device running configuration retains the authorized interface intent. Identify configuration ownership and update the approved Central source before reconciling the device.
Running switch policy matches branch requirements and unauthorized VLAN traffic fails. It would not verify that post synchronization device running configuration retains the authorized interface intent. Local edit disappears after the next Central synchronization event, and the pair must correct that exact failure. During a distribution switch deployment for a corporate voice and data network team, a fault trace confirms that a technician changes an Aruba CX interface locally while its Central managed template continues to enforce.
Question 359
During a routing and performance escalation for a multisite service assurance team, a fault trace confirms that a relocated laptop is connected to a port assigned to the voice VLAN instead of the employee access VLAN. The team needs a supported change with independently measurable acceptance evidence. What finding should an engineer use to distinguish the root cause?
Explanation
Correct Answer
Port VLAN membership differs from the asset location plan and DHCP offers carry the voice subnet. During a routing and performance escalation for a multisite service assurance team, a fault trace confirms that a relocated laptop is connected to a port assigned to the voice VLAN instead of the employee access VLAN.
Incorrect Answers
“Interface capabilities list different supported speeds while optical signal remains present” does not demonstrate what is needed when during a routing and performance escalation for a multisite service assurance team, a fault trace confirms that a relocated laptop is connected to a port assigned to the voice VLAN instead of the employee access VLAN. Port VLAN membership differs from the asset location plan and DHCP offers carry the voice subnet.
“PoE controller shows allocation unavailable while endpoint interfaces are otherwise linked” concerns a different part of the problem. During a routing and performance escalation for a multisite service assurance team, a fault trace confirms that a relocated laptop is connected to a port assigned to the voice VLAN instead of the employee access VLAN. Port VLAN membership differs from the asset location plan and DHCP offers carry the voice subnet.
During a routing and performance escalation for a multisite service assurance team, a fault trace confirms that a relocated laptop is connected to a port assigned to the voice VLAN instead of the employee access VLAN. The proposed action “LACP partner system IDs disagree across the two intended bundle members” would not resolve that situation. Port VLAN membership differs from the asset location plan and DHCP offers carry the voice subnet.
Question 360
In a university campus infrastructure team, engineers discover during a wired network topology design review that an engineer diagrams two aggregation switches but never validates host reachability during one device failure. The project must protect approved network access while addressing the specific cause. Which evidence most specifically identifies this fault instead of a similar switch problem?
Explanation
Correct Answer
Design acceptance contains only steady state link up tests despite a high availability requirement. An engineer diagrams two aggregation switches but never validates host reachability during one device failure.
Incorrect Answers
Capacity workbook estimates peak aggregate traffic above available uplink throughput. An engineer diagrams two aggregation switches but never validates host reachability during one device failure. Design acceptance contains only steady state link up tests despite a high availability requirement.
“Device subnet and gateway location diagram reveals every local VLAN depends on a remote link” does not demonstrate what is needed when an engineer diagrams two aggregation switches but never validates host reachability during one device failure. Design acceptance contains only steady state link up tests despite a high availability requirement.
“Office topology has one wiring closet and no fabric endpoint segmentation or scale requirement” does not explain the observed failure: an engineer diagrams two aggregation switches but never validates host reachability during one device failure. Design acceptance contains only steady state link up tests despite a high availability requirement.
HPE Network Switching Professional (HPE7-A08) Practice Tests
- HP HPE7-A08 Practice Test 34 - 10 Questions (Last Reviewed 19-Oct-2026)
- HP HPE7-A08 Practice Test 35 - 10 Questions (Last Reviewed 18-Oct-2026)
- HP HPE7-A08 Practice Test 36 - 10 Questions (Last Reviewed 17-Oct-2026)
- HP HPE7-A08 Practice Test 37 - 10 Questions (Last Reviewed 16-Oct-2026)
- HP HPE7-A08 Practice Test 38 - 10 Questions (Last Reviewed 15-Oct-2026)
