Cisco 200-301 Practice Test 65 - Prepaway
Practice Exams:

Pass Cisco 200-301 Exam in First Attempt Guaranteed!

Get 100% Latest Exam Questions, Accurate & Verified Answers!

30 Days Free Updates, Instant Download!

Verified By Experts
Premium Bundle
$29.98
$79.99 $109.97

200-301 Premium Bundle


  • Premium File 760 Questions & Answers. Last update: Nov 10, 2026
  • Training Course 271 Lectures
  • Study Guide 1969 Pages

Cisco 200-301 Practice Test 65

Question 640

Network review: A standard ACL permits one branch prefix, and administrators cannot reach the switch from a second authorized subnet. Which TWO proposed shortcuts would be unsafe in this situation? Select TWO answers.

  1. For this protected network, assume traffic not listed in the ACL is implicitly permitted.
  2. For this protected network, add explicit least-privilege permits before the implicit deny, in correct first-match order.
  3. For this protected network, collect targeted evidence to inspect ACE sequence, implicit deny behavior, interface direction and hit counters for matching and missing sources.
  4. For this protected network, place a broad deny any before all intended permit entries.
  5. For this protected network, confirm the repair by checking that show access-lists counters and selected traffic probes prove authorized subnets match a permit and unauthorized sources are denied.

Explanation

Correct Answer

A:

“For this protected network, assume traffic not listed in the ACL is implicitly permitted” would violate the requirement. For this protected network, cisco IPv4 access lists have an implicit deny at the end; packets not matching a permit earlier are denied.

D:

“For this protected network, place a broad deny any before all intended permit entries” would violate the requirement. For this protected network, cisco IPv4 access lists have an implicit deny at the end; packets not matching a permit earlier are denied.

Incorrect Answers

B:

“For this protected network, add explicit least-privilege permits before the implicit deny, in correct first-match order” is the controlled implementation, not an unsafe workaround. For this protected network, cisco IPv4 access lists have an implicit deny at the end; packets not matching a permit earlier are denied.

C:

“For this protected network, collect targeted evidence to inspect ACE sequence, implicit deny behavior, interface direction and hit counters for matching and missing sources” adds a relevant safeguard or verification step rather than weakening the solution. For this protected network, cisco IPv4 access lists have an implicit deny at the end; packets not matching a permit earlier are denied.

E:

“For this protected network, confirm the repair by checking that show access-lists counters and selected traffic probes prove authorized subnets match a permit and unauthorized sources are denied” adds a relevant safeguard or verification step rather than weakening the solution. For this protected network, cisco IPv4 access lists have an implicit deny at the end; packets not matching a permit earlier are denied.

Question 641

Consider this operational failure: An access port should allow one learned workstation MAC and errdisable when an unauthorized device appears. What should the administrator implement first?

  1. Enable port security on a trunk without confirming platform support or uplink role.
  2. Treat PortFast alone as a replacement for source MAC enforcement.
  3. Enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.
  4. Set maximum secure MACs to a very high value and assume it enforces single-device access.

Explanation

Correct Answer

C:

The action 'Enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.' directly addresses the switch port security sticky mac requirement in this situation: An access port should allow one learned workstation MAC and errdisable when an unauthorized device appears. The relevant network mechanism is that port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions. A successful change should show that show port-security interface shows allowed MAC and violation counters; attaching an unknown source produces the expected response. To distinguish a genuine correction from a superficial change, inspect show port-security interface, show port-security address, MAC table, violation mode and interface err-disabled state.

Incorrect Answers

A:

“Enable port security on a trunk without confirming platform support or uplink role” does not implement the control that the facts call for. Instead, enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.

B:

“Treat PortFast alone as a replacement for source MAC enforcement” does not implement the control that the facts call for. Instead, enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.

D:

“Set maximum secure MACs to a very high value and assume it enforces single-device access” would not meet the requirement. Instead, enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.

Question 642

While troubleshooting 'An access port should allow one learned workstation MAC and errdisable when an unauthorized device appears.', which underlying protocol rule should guide the decision?

  1. Extended ACL entries can distinguish IP destinations and transport ports; interface and direction placement must match the actual flow.
  2. DHCP snooping blocks server replies on untrusted ports while recording lease bindings for correctly authorized clients.
  3. Cisco IPv4 access lists have an implicit deny at the end; packets not matching a permit earlier are denied.
  4. Port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

Explanation

Correct Answer

D:

Port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions. Show port-security interface shows allowed MAC and violation counters; attaching an unknown source produces the expected response.

Incorrect Answers

A:

The choice “Extended ACL entries can distinguish IP destinations and transport ports; interface and direction placement must match the actual flow” concerns extended acl protocol; it does not resolve the stated requirement. Port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

B:

The choice “DHCP snooping blocks server replies on untrusted ports while recording lease bindings for correctly authorized clients” concerns dhcp snooping trusted uplinks; it does not resolve the stated requirement. Port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

C:

The choice “Cisco IPv4 access lists have an implicit deny at the end; packets not matching a permit earlier are denied” concerns implicit deny at acl end; it does not resolve the stated requirement. Port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

Question 643

Which measurable result should be checked before closing this ticket: An access port should allow one learned workstation MAC and errdisable when an unauthorized device appears.

  1. show access-lists hit counts and positive/negative traffic tests demonstrate exact permitted service and blocked alternative.
  2. Clients obtain legitimate leases, rogue DHCP offers are dropped, and show ip dhcp snooping binding records client MAC/IP/VLAN/port.
  3. show access-lists counters and selected traffic probes prove authorized subnets match a permit and unauthorized sources are denied.
  4. show port-security interface shows allowed MAC and violation counters; attaching an unknown source produces the expected response.

Explanation

Correct Answer

D:

Show port-security interface shows allowed MAC and violation counters; attaching an unknown source produces the expected response. Enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.

Incorrect Answers

A:

“Show access-lists hit counts and positive/negative traffic tests demonstrate exact permitted service and blocked alternative” pertains to extended acl protocol, not the deciding condition here. Show port-security interface shows allowed MAC and violation counters; attaching an unknown source produces the expected response.

B:

The choice “Clients obtain legitimate leases, rogue DHCP offers are dropped, and show ip dhcp snooping binding records client MAC/IP/VLAN/port” concerns dhcp snooping trusted uplinks; it does not resolve the stated requirement. Show port-security interface shows allowed MAC and violation counters; attaching an unknown source produces the expected response.

C:

“Show access-lists counters and selected traffic probes prove authorized subnets match a permit and unauthorized sources are denied” pertains to implicit deny at acl end, not the deciding condition here. Show port-security interface shows allowed MAC and violation counters; attaching an unknown source produces the expected response.

Question 644

Before modifying more devices to address 'An access port should allow one learned workstation MAC and errdisable when an unauthorized device appears.', which diagnostic evidence is most relevant?

  1. Inspect show ip dhcp snooping, trust state, binding table, rate limits and DHCP offer captures.
  2. Inspect show port-security interface, show port-security address, MAC table, violation mode and interface err-disabled state.
  3. Inspect ACE sequence, implicit deny behavior, interface direction and hit counters for matching and missing sources.
  4. Inspect source/destination masks, tcp/udp matches, eq port, access-group interface/direction and ACE order.

Explanation

Correct Answer

B:

The investigation 'Inspect show port-security interface, show port-security address, MAC table, violation mode and interface err-disabled state.' examines the variables most likely to explain switch port security sticky mac in this situation: An access port should allow one learned workstation MAC and errdisable when an unauthorized device appears. Those checks are directly tied to the behavior that port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions. The engineer can correlate this evidence with the expected outcome that show port-security interface shows allowed MAC and violation counters; attaching an unknown source produces the expected response. and decide whether to enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.

Incorrect Answers

A:

“Inspect show ip dhcp snooping, trust state, binding table, rate limits and DHCP offer captures” pertains to dhcp snooping trusted uplinks, not the deciding condition here. Port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

C:

The choice “Inspect ACE sequence, implicit deny behavior, interface direction and hit counters for matching and missing sources” concerns implicit deny at acl end; it does not resolve the stated requirement. Port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

D:

“Inspect source/destination masks, tcp/udp matches, eq port, access-group interface/direction and ACE order” pertains to extended acl protocol, not the deciding condition here. Port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

Question 645

A change board considers the issue 'An access port should allow one learned workstation MAC and errdisable when an unauthorized device appears.'. Identify the TWO decisions that should be rejected. Select TWO answers.

  1. Confirm the repair by checking that show port-security interface shows allowed MAC and violation counters; attaching an unknown source produces the expected response.
  2. Enable port security on a trunk without confirming platform support or uplink role.
  3. Enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.
  4. Set maximum secure MACs to a very high value and assume it enforces single-device access.
  5. Collect targeted evidence to inspect show port-security interface, show port-security address, MAC table, violation mode and interface err-disabled state.

Explanation

Correct Answer

B:

“Enable port security on a trunk without confirming platform support or uplink role” would violate the requirement. The appropriate control instead is to enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.

D:

“Set maximum secure MACs to a very high value and assume it enforces single-device access” would violate the requirement.

Incorrect Answers

A:

“Confirm the repair by checking that show port-security interface shows allowed MAC and violation counters; attaching an unknown source produces the expected response” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that show port-security interface shows allowed MAC and violation counters; attaching an unknown source produces the expected response.

C:

“Enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode” is the controlled implementation, not an unsafe workaround. Confirm that show port-security interface shows allowed MAC and violation counters; attaching an unknown source produces the expected response.

E:

“Collect targeted evidence to inspect show port-security interface, show port-security address, MAC table, violation mode and interface err-disabled state” adds a relevant safeguard or verification step rather than weakening the solution.

Question 646

A network operator receives this ticket: A lobby jack may be used by one trusted badge reader; a small unmanaged switch should not add multiple source MACs. Which configuration is best suited to the reported issue?

  1. For this protected network, enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.
  2. For this protected network, set maximum secure MACs to a very high value and assume it enforces single-device access.
  3. For this protected network, treat PortFast alone as a replacement for source MAC enforcement.
  4. For this protected network, enable port security on a trunk without confirming platform support or uplink role.

Explanation

Correct Answer

A:

The action 'For this protected network, enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.' directly addresses the switch port security sticky mac requirement in this situation: A lobby jack may be used by one trusted badge reader; a small unmanaged switch should not add multiple source MACs. The relevant network mechanism is that port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions. A successful change should show that show port-security interface shows allowed MAC and violation counters; attaching an unknown source produces the expected response. To distinguish a genuine correction from a superficial change, inspect show port-security interface, show port-security address, MAC table, violation mode and interface err-disabled state.

Incorrect Answers

B:

“For this protected network, set maximum secure MACs to a very high value and assume it enforces single-device access” would not meet the requirement. Instead, for this protected network, enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.

C:

“For this protected network, treat PortFast alone as a replacement for source MAC enforcement” does not implement the control that the facts call for. Instead, for this protected network, enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.

D:

“For this protected network, enable port security on a trunk without confirming platform support or uplink role” does not implement the control that the facts call for. Instead, for this protected network, enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.

Question 647

Which network-layer or protocol behavior most directly explains the result in this case: A lobby jack may be used by one trusted badge reader; a small unmanaged switch should not add multiple source MACs.

  1. For this protected network, extended ACL entries can distinguish IP destinations and transport ports; interface and direction placement must match the actual flow.
  2. For this protected network, port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.
  3. For this protected network, dHCP snooping blocks server replies on untrusted ports while recording lease bindings for correctly authorized clients.
  4. For this protected network, cisco IPv4 access lists have an implicit deny at the end; packets not matching a permit earlier are denied.

Explanation

Correct Answer

B:

For this protected network, port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

Incorrect Answers

A:

The choice “For this protected network, extended ACL entries can distinguish IP destinations and transport ports; interface and direction placement must match the actual flow” concerns extended acl protocol; it does not resolve the stated requirement. For this protected network, port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

C:

The choice “For this protected network, dHCP snooping blocks server replies on untrusted ports while recording lease bindings for correctly authorized clients” concerns dhcp snooping trusted uplinks; it does not resolve the stated requirement. For this protected network, port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

D:

The choice “For this protected network, cisco IPv4 access lists have an implicit deny at the end; packets not matching a permit earlier are denied” concerns implicit deny at acl end; it does not resolve the stated requirement. For this protected network, port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

Question 648

After correcting 'A lobby jack may be used by one trusted badge reader; a small unmanaged switch should not add multiple source MACs.', which observation is the strongest evidence that the specific requirement is met?

  1. For this protected network, show access-lists hit counts and positive/negative traffic tests demonstrate exact permitted service and blocked alternative.
  2. For this protected network, clients obtain legitimate leases, rogue DHCP offers are dropped, and show ip dhcp snooping binding records client MAC/IP/VLAN/port.
  3. For this protected network, show port-security interface shows allowed MAC and violation counters; attaching an unknown source produces the expected response.
  4. For this protected network, show access-lists counters and selected traffic probes prove authorized subnets match a permit and unauthorized sources are denied.

Explanation

Correct Answer

C:

Because a network operator receives this ticket: A lobby jack may be used by one trusted badge reader; a small unmanaged switch should not add multiple source MACs, for this protected network, port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

Incorrect Answers

A:

The choice “For this protected network, show access-lists hit counts and positive/negative traffic tests demonstrate exact permitted service and blocked alternative” concerns extended acl protocol; it does not resolve the stated requirement. For this protected network, port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

B:

The choice “For this protected network, clients obtain legitimate leases, rogue DHCP offers are dropped, and show ip dhcp snooping binding records client MAC/IP/VLAN/port” concerns dhcp snooping trusted uplinks; it does not resolve the stated requirement. For this protected network, port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

D:

The choice “For this protected network, show access-lists counters and selected traffic probes prove authorized subnets match a permit and unauthorized sources are denied” concerns implicit deny at acl end; it does not resolve the stated requirement. For this protected network, port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

Question 649

An operator is triaging the issue 'A lobby jack may be used by one trusted badge reader; a small unmanaged switch should not add multiple source MACs.'. What should be inspected to isolate the actual cause?

  1. For this protected network, inspect source/destination masks, tcp/udp matches, eq port, access-group interface/direction and ACE order.
  2. For this protected network, inspect ACE sequence, implicit deny behavior, interface direction and hit counters for matching and missing sources.
  3. For this protected network, inspect show ip dhcp snooping, trust state, binding table, rate limits and DHCP offer captures.
  4. For this protected network, inspect show port-security interface, show port-security address, MAC table, violation mode and interface err-disabled state.

Explanation

Correct Answer

D:

For this protected network, inspect show port-security interface, show port-security address, MAC table, violation mode and interface err-disabled state. For this protected network, port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

Incorrect Answers

A:

The choice “For this protected network, inspect source/destination masks, tcp/udp matches, eq port, access-group interface/direction and ACE order” concerns extended acl protocol; it does not resolve the stated requirement. For this protected network, inspect show port-security interface, show port-security address, MAC table, violation mode and interface err-disabled state.

B:

The choice “For this protected network, inspect ACE sequence, implicit deny behavior, interface direction and hit counters for matching and missing sources” concerns implicit deny at acl end; it does not resolve the stated requirement. For this protected network, inspect show port-security interface, show port-security address, MAC table, violation mode and interface err-disabled state.

C:

The choice “For this protected network, inspect show ip dhcp snooping, trust state, binding table, rate limits and DHCP offer captures” concerns dhcp snooping trusted uplinks; it does not resolve the stated requirement. For this protected network, inspect show port-security interface, show port-security address, MAC table, violation mode and interface err-disabled state.

Question 650

For this incident: A lobby jack may be used by one trusted badge reader; a small unmanaged switch should not add multiple source MACs. Which TWO practices introduce avoidable network risk? Select TWO answers.

  1. For this protected network, collect targeted evidence to inspect show port-security interface, show port-security address, MAC table, violation mode and interface err-disabled state.
  2. For this protected network, enable port security on a trunk without confirming platform support or uplink role.
  3. For this protected network, enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.
  4. For this protected network, set maximum secure MACs to a very high value and assume it enforces single-device access.
  5. For this protected network, confirm the repair by checking that show port-security interface shows allowed MAC and violation counters; attaching an unknown source produces the expected response.

Explanation

Correct Answer

B:

“For this protected network, enable port security on a trunk without confirming platform support or uplink role” would violate the requirement. The appropriate control instead is to for this protected network, enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.

D:

“For this protected network, set maximum secure MACs to a very high value and assume it enforces single-device access” would violate the requirement. The appropriate control instead is to for this protected network, enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode.

Incorrect Answers

A:

“For this protected network, collect targeted evidence to inspect show port-security interface, show port-security address, MAC table, violation mode and interface err-disabled state” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that for this protected network, port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

C:

“For this protected network, enable port security with the intended maximum count, sticky MAC where needed and a documented violation mode” is the controlled implementation, not an unsafe workaround. Confirm that for this protected network, port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

E:

“For this protected network, confirm the repair by checking that show port-security interface shows allowed MAC and violation counters; attaching an unknown source produces the expected response” adds a relevant safeguard or verification step rather than weakening the solution. Confirm that for this protected network, port security learns or configures allowed source MACs on a switchport and enforces a maximum using protect, restrict or shutdown actions.

Cisco Certified Network Associate (CCNA) (200-301) Practice Tests